Plans

Free Woodworking Plans to Build a Stackable Cube Chair

09.07.10 By //

This is the chameleon of furniture pieces..Chair, Stack-able Cube, Ottoman, Bookshelf…I suppose the options are virtually limitless. This should be very easy to build with the right tools, and fairly budget friendly as well.

Believe it or not, this is one single design arranged several ways.

Estimated Cost

Under $25

Tools
  • Tape Measure
  • Drill
  • Kreg Jig
  • Saw
  • Miter Saw – optional – if you prefer to bevel the front edge of the Seat portion of the stackable cube chair. Not required.
Lumber

For one cube/chair

  • 1 – 2×10 at 8′
  • 1 – 2×10 at 6′
Materials
  • 2 1/2″ Pocket Hole Screws
  • Wood Glue
  • Wood Filler
  • Sandpaper
  • Finishing Supplies
Cut List
  • 2 – 2×10 at 31 1/2″ (Back Boards)
  • 2 – 2×10 at 15 3/4″ (Front Boards)
  • 2 – 2×10 at 15 1/2″ (Base Boards)
  • 2 – 2×10 at 17″ (Seat)
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Attach your Back Boards to each other staggering your Pocket Holes. Do the same for your Front Boards, the Base Boards, and the Seat. Bevel the Seat and Front Boards if you are choosing to do so. Create your Pocket holes for fastening these ‘pairs’ to each other as well. Then fasten the Back Boards to the Base Boards and the Base Boards to the Seat.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.