This piece rolls nicely underneath the Headboard Base for easy pull out but hidden storage! Simple to build and one on each side of the headboard base will give you a ton of extra storage for whatever you may need it for. Stuffed animals, laundry, other random things that don’t have a home…this is the solution for them, and is a fun addition to our Stuff your Stuff Collection!

The Deets

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost


  • Tools 
  • Tape Measure
  • Sander
  • Drill
  • Kreg Jig – optional and you can secure using wood screws and a countersink bit.
  • Jig Saw 


  • 1 Sheet of 3/4” Ply or MDF (this should make 2 units) or for only one, purchase about a 1/2 sheet.
  • 1 1/4” Pocket Hole Screws or 2” Wood Screws or 2” Finish Nails
  • 4 – 2” Casters
  • Wood Glue
  • Wood Filler
  • Sanding Supplies
  • Finishing Supplies


Cut List
  • 2 – 3/4” Ply or MDF at 18” x 18 1/2” Front and Back Panels
  • 2 – 3/4” Ply or MDF at 18” x 11 1/2” Sides
  • 1 – 3/4” Ply or MDF at 10” x 18 1/2” Bottom

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Build the Structure: Cut or Carve out the Handle Holds, they are approximately 4” in diameter half circles, but you can adjust this as needed. Fasten your front and back (yellow) to the sides (blue) using your Kreg Jig set for 3/4” stock and your 1 1/4” pocket hole screws and glue.

Step 2

Fasten the Bottom in Place: Use 1 1/4” Pocket hole screws and glue to fasten the bottom inset and up about 3/4” from the bottom edges of the box. This gives you a bit of room to hide the casters a tiny bit. Then simply follow the directions on your particular casters and fasten them in place accordingly.

Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 11
Step 12
Step 13
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School


**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter