May
31
2011
Project Image

This table was brought to us by our BFF Loren, isn’t she amazing? Yes! I adore the sawhorse/ trellis style blend this table has, and I adore the portability of it! Pull it out when you need it, fold it away when not in use…genius! And a pretty simple build as well! I also think this would make an incredible craft table or portable conference table, even a great place to dine outdoors! So many things I can imagine using this beauty for!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Sander
  • Drill
  • Jig Saw – can also use your sander if need be.
  • Miter Saw – can also use a circular saw, table saw or even a jig saw if need be.
  • Table Saw – can also use a circular saw, jig saw, or even hand saw if need be
  • Kreg Jig - optional
Lumber
  • 2 – 1x4 at 8’
  • 1 – 1x4 at 10’ OR 2 at 6’ OR 2 more at 8’ if they are cheaper or easier to transport.
  • 1 Sheet 3/4” Ply – can also use edge glued laminate project boards or boards glue and screwed together using your kreg jig, at a size of your choice, just be sure to adjust the apron dimensions and if need be the stretchers as well.
Materials
  • 2″ Wood Screws
  • 1 1/4” Pocket Hole Screws
  • ** 2” Finish Nails – optional if you aren’t using a Kreg Jig® 
  • 4 – Bolts 1 1/2” length
  • 4 – large washers
  • 4 – lock nuts appropriately sized for the diameter of your bolt (likely 1/4” – 1/2” depending on the style you choose) 
  • Wood Glue 
  • Wood Filler
  • Sanding Supplies
  • Finishing Supplies
Cut List
  • 1 – 3/4” Ply at 30” x 69” Top
  • 2 – 1x4 at 66” Aprons
  • 2 – 1x4 at 19 1/2” Aprons
  • 4 – 1x4 at 32” Legs (this will be cut down to the appropriate length when you miter as shown in the diagram)
  • 4 – 1x4 at 21 3/4” Leg Stretchers
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Build the Top: If you are using a Kreg Jig® create your pocket holes in the yellow aprons to connect them to the blue aprons, as well as around the inside of both yellow and blue aprons, spaced 6-8” apart. Construct your Table Top Frame by attaching the aprons using your 1 1/4″ pocket hole screws and glue. Then attach the Table Top frame to the Top itself using your 1 1/4” pocket hole screws and glue. If you aren't using a pocket hole system, use 2” screws and glue to construct the frame, be sure to countersink, and then attach the frame to the Table Top using 2” Finish Nails and glue.

Step 1
Step 2

Construct the Leg Units: The Legs themselves will require a 10 Degree Cut at the bottom and a rounded edge at the top. The rounded edge at the top should have a 1 1/2” radius and can be created using a sander or a jig saw. Once your legs are mitered and rounded, you can attach the lower leg stretcher (blue) using 2” screws and glue, be sure to countersink. Before you attach your top leg stretcher (yellow) you should create a 10 Degree Bevel along the top edge. This will act as a stop when the legs are un folded and the table is in the upright position. You can create a 10 Degree Bevel using a table saw, circular saw, even a jig saw or hand saw if need be (I suppose if you were diligent, you might also get the job done with your sander if none of the tools mentioned are available to you) and you are simply trying to give that top edge of the top stretchers a flush method of stopping so that the legs are slightly splayed as you see in Loren’s finished pictures. Once you have created your bevel attach the stretcher to the legs using 2” screws and glue and place them 14 1/2” from the lower stretchers.

Step 2
Step 3

Attach the Leg Units: To attach the Leg units, you will simply need to drill a hole through both the legs and the aprons in the location where the legs will attach. The bottom outside edge of your legs should roughly align to the aprons above when they are sitting at the appropriate angle. To attach the legs, Loren simply used a bolt, washer and lock nut! Easy peasy, lemon squeezy! You can see how this will look in the image below and frankly I think it adds to the appeal of the table…adore! You will need to drill a hole that is roughly the size of the bolt shaft diameter or a tad larger. The legs will be offset and opposite on each side as you can see below..in other words one leg unit on the outside of the apron on the left and the opposite leg on the outside of the apron on the right side. This allows for the legs to collapse easily when you fold them in.

Step 3
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter