Plans

Free Woodworking Plans to Build a PotteryBarn Inspired Chesapeake 60 Inch Dining Table

06.01.11 By //
Project Image

This simple table is a stunner with it’s clean lines and slightly coastal feel! This is the perfect little dining or entertaining piece for outside, perhaps with the banquettes or benches, or even configured with a corner unit into a nook like arrangement. Another fabulous addition to our Chesapeake Collection and one that would look equally as fabulous inside or out! Did I mention that this will cost you less than $40 to build? Yep, true story!

Estimated Cost 

$25-$50

Dimensions 
Dimensions for This Project

Tools 

Tape Measure

Sander

Drill

Jig Saw – optional and if you prefer a more angular legs you can use a circular saw or table saw as well and you can actually also use your sander to get the job done if need be!

Kreg Jig® (pocket hole system)

Lumber 

2 – 4×4 at 6’ (your store may only sell these in 8’ lengths so you will have extra)

3 – 1×3 at 8’

1 – 1×3 at 6’

2 – 1×4 at 8’

2 – 1×4 at 6’

2 – 1×6 at 8’

1 – 1×6 at 6’

Materials 

1 1/4” Pocket Hole Screws – Stainless Steel or Blue Kote if this is for outdoor use

2” Wood Screws or Nails or Finish Nails – galvanized or coated if for outdoor use

Wood Glue – suitable for outdoor use if need be

Sanding Supplies

Finishing Supplies

Cut List 

4 – 4×4 at 29 1/4” Legs

2 – 1×4 at 26 1/2” Side Aprons

2 – 1×4 at 51 3/4” Front and Back Aprons

2 – 1×4 at 55 3/4” Interior Table Frame Supports

36 – 1×3 at 9 1/2” Table Top Interior Boards

3 – 1×6 at 49 3/4” Outer and Center Table Top Boards

2 – 1×6 at 35 1/2” Outer Side Table Top Boards

Instructions 

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials!

Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices.

Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Step 1 

Cut out Your Legs: Begin with your 4×4 and starting at 3 1/2” from the top of each leg, carve on the inside edges of each leg, at an angle downward so that the bottom of each leg is a full 1” smaller than the top. The outside of each leg will remain straight and only the inside edges will angle. This is optional and for decorative purposes only.

Step 2

Step 2 

Fasten Aprons and Frame Supports in Place: Use your Kreg Jig® set for 3/4” stock and your 1 1/4” pocket hole screws and glue to fasten to the Legs and to fasten the interior frame supports to the side aprons. Set the Aprons in 3/4” from the outside of the legs.

Step 3

Step 3 

Construct the Table Top: Using your Kreg Jig® set for 3/4” stock and your 1 1/4” pocket hole screws and glue, fasten the Boards together as shown below. Space the Interior Table Top Boards 1/4” Apart. To attach to the legs and frame, you can simply use your 2” finish nails or 2” screws to fasten directly to the legs, aprons, and interior supports. Be sure you center the top and place the pocket holes face down when fastening in place. To create an umbrella hole, use a 2” or 2 1/4” hole saw bit or spade bit and create a hole directly in the center of the table. I recommend doing this once the table top has been put together and perhaps even after you have fastened the top in place. It will be easier to do this way.

Finishing Instructions 

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

If you enjoyed this post PLEASE STUMBLE IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also:

Follow my blog with blog lovin!

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.