Nov
29
2011
Project Image

This is inspired by perhaps one of the cutest play kitchens I have seen and I am thankful that this was submitted as a project request! You guys have better eyes and ears than I at times and I'm glad when you share something fabulous with me!

We will be covering 2 styles for this play kitchen: the gourmet and the cottage kitchen. Each will have 2 sections, a base and a hutch with storage and a microwave, perhaps even a few accessories if I'm feeling particularly feisty!

Each style will be generally the same in construction and will only differ in how they are trimmed out.

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools

Safety Gear

Tape Measure

Drill

Saw

Jig Saw

Kreg Jig - optional but recommended

Nail Gun - optional but recommended

Lumber

2 - 1x12 at 8'

3 - 1x2 at 8'

1 - 1x3 at 6'

1 - 1x4 at 6'

1 1/4 sheet of 1/4" ply

Materials

3 - Drawer Pulls in various sizes for the oven door, and top and bottom cabinets.

Small Sink and Faucet

2 - Stove burners or grates

2 - oven knobs

6 Hinges

2" wood screws - not necessary if using Kreg Jig

1 1/4" pocket hole screws

1 1/4" finish nails

Wood Glue

Wood Filler

Cut List

1 - 1x12 at 33 1/2" Top

2 - 1x12 at 24" Sides

2 - 1x12 at 19" Center Dividers

1 - 1x12 at 32" Bottom

2 - 1x12 at 10 1/4" Outside Shelves

1 - 1x12 at 10" Center Shelf

1 - 1x2 at 33 1/2" Top Trim

1 - 1x2 at 35" Bottom Trim

2 - 1x2 at 12" Bottom Trim

6 - 1x2 at 8 3/4" Doors

2 - 1x2 at 13 1/2" Oven Door

2 - 1x2 at 6 1/8" Top Cab Door

2 - 1x2 at 10 3/4" Lower Cab Door

1 - 1x3 at 33 1/2" Upper Facing

1 - 1x4 at 11 3/4" Oven Knob Facing

1 - 1x4 at 32" Footer Trim

1 - 1/4" ply at 11 1/4" x 9 1/4" Oven Facing

1 - 1/4" ply at 4 1/8" x 9 3/4" Top Cab Door

1 - 1/4" ply at 8 3/4" x 9 3/4" Lower Cab Door

Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials!

Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices.

Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Build the Base Unit: Use your Kreg Jig set for 3/4" stock and your 1 1/4" pocket hole screws and glue to build the box as shown below. If you aren't using a Kreg Jig you can use 2" wood screws and glue, just be sure to countersink.

Mark out your sink hole and carve out using your jig saw so that you can set your sink into the hole.

Step 1
Step 2

Add the Shelves: The outside shelves are the same size, but all 3 shelves are in different locations. Fasten them in place using your Kreg Jig set for 3/4" stock and your 1 1/4" pocket hole screws and glue. If you aren't using a KJ you can use your 2" wood screws and glue, just be sure to countersink.

Step 2
Step 3

Add the Facing and Footer: Use your 1 1/4" finish nails and glue to tack on the upper and oven knob facing directly to the base unit and from the outside of the sides to attach the footer underneath the bottom board of the base unit.

If you want to give this a truly gourmet look, you might consider painting the Oven Knob Facing in a metallic silver (typically comes in a spray paint can) prior to attaching it (since you will likely have to spray it.

Step 3
Step 4

Construct the Doors: You will build all 3 doors by constructing the face frames for each using your Kreg Jig set for 3/4" stock and your 1 1/4" pocket hole screws and glue.

To construct a face frame you will place your pocket holes in the rails (horizontal pieces) and fasten them to the stiles (vertical). For the Cabinet Doors, you will then glue on the backing from the back side of the face frames and they will sit with 1/2" overhang all the way around the opening for the Upper and Lower Cabinet Doors.

To hang your doors, simply allow for gaps as indicated below and attach using simple hinges for overlay cabinet doors.

The oven door will need the hinges on the bottom (obviously) and the cabinet doors should have the hinges on the outside edge.

Step 4
Step 5

Cut and Carve the Oven Door Facing and Tack onto the Oven Door using glue. You can paint this piece in a silver metallic finish to get a truly gourmet look!

Step 5
Step 6

Add the trim pieces shown below: Use glue and your 1 1/4" finish nails.

Step 6
Step 7

Now it's time to add your fun hardware! You can purchase replacement parts for ovens, stoves, and sinks at your local hardware store and these are perfect for little play parts. I recommend creating a painted section to sit underneath the stove burners and for the facing underneath where the knobs will sit. This will give your piece that fabulous gourmet kitchen look!

Step 7
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Note

If you enjoyed this post PLEASE STUMBLE IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also:

Follow my blog with blog lovin!

Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter