• Essentials from Target for The Design Confidential Feeling Fall // Essentials for Creating a Cozy Mantel
  • Free DIY Furniture Plans // How to Build an Indoor Outdoor House Bed Playhouse + Outdoor Daybed Lounge
  • Family Room Sneak Peek / The Design Confidential in Collaboration with Joss and Main for a Curators Collection Sale Story Interview
  • Hammock and Lounging Area for the Home Depot Style Challenge Outdoor Games Edition
  • DIY Faux Watercolor Wallpaper Wall Treatment with Paint
  • Free DIY Furniture Plans // How to Build a Tri Trestle Table
  • DIY Home Decor // How To Make Your Own Removable Wallpaper
Dec
22
2011
Project Image

Here is our version of the Carolina Craft Table but this time with the addition of interchangeable legs! The design is exactly the same as the original Carolina Craft Table but it is assembled in a different way to allow for the legs to be removed and replaced that way this table can grow with your little one!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$50-$75

Dimensions
Dimensions for This Project
Tools
  • Safety Gear
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Hammer or Brad nailer
Lumber
  • **1 - 3x3 Posts at 8’
  • 1 - 1x3 at 4’
  • 1 - 1x3 at 8’
  • 1 - 1x4 at 4’
  • 1 - 1x4 at8’
  • 1 - 1” Round Dowel Rod at 2'
  • 1/4 sheet of 1/4” plywood
  • Full sheet of 3/4” plywood
  • **If 3x3 posts are not available in your area or are too expensive, 1x3 lumber can be face-glued to 2x3 lumber to create posts. Keep in mind that the depth will differ by 1/4” so the aprons need to be adjusted accordingly (longer by 1/2" total).
  •  **Purchase 1 additional 1x3 at 8’ and 1 additional 2x3 at 8' for this step.
Materials
  • 1 1/4” pocket hole screws
  • 1 1/2” screws
  • 1 1/4” spade bit or hole saw
  • 1 1/2” brad nail
  • Drawer knobs or handles
  • Wood filler
  • Sanding Supplies
  • Wood glue
  • Finishing Supplies
Cut List
  • 4 – 3x3 at 22 1/4” (Legs)
  • 1 - 1x4 at 40” (Long Apron)*
  • 2 - 1x4 at 20” (Short Aprons)
  • 4 - 1x4 at 23½” (Table Top Supports)
  • 3 - 1x4 at 4” (Apron Pieces on Drawer End)
  • 1 - 3/4" plywood at 27”x49” (Top)
  • 2 - 1x4 at 14” (Drawer Faces)
  • 4 - 1x3 at 11½” (Drawer Sides)
  • 4 - 1x3 at 13” (Drawer Box Fronts and Backs)
  • 2 - 1/4" plywood 13”x13” (Drawer Bottoms)
  • ** If making your own posts from 1x3 lumber, add ½” the length of these pieces.
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. 

If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless.

Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

 Using the saw of your choice, cut the top from ¾” plywood.

Step 1
Step 2

 Cut the apron pieces as listed above and add pocket holes to each end (sized for 3/4" stock) and one of the long edges. (These will face to the inside.) Attach the aprons to the table top as indicated using 1 1/4” pocket hole screws. The long aprons will have angle brackets attached to the ends which will attach to the legs. Because of the table supports and drawers, pocket holes will not work here. You will not be able to get the drill in the small space to add or remove screws when replacing the legs.

 Don’t forget to use glue for an extra strong joint!

Step 2
Step 3

 Cut the pieces for the paper roll. Use a compass to draw a 1 1/4” radius on one end and cut out with a jig saw. Bore a 1 1/4” hole through each piece. Secure to one end of the table, at the short apron, by screwing it to the apron from the inside. You can also secure it with a brad nailer that shoots 1½” brads.

Step 3
Step 4

Cut the top supports and add pocket holes to each end (sized for 3/4" stock). Also add pocket holes to one long end of each board to secure the table top (sized for 3/4" stock). Cut the 4” apron pieces that will be placed next to the drawers. Drill pocket holes in only two of these boards, on one end only so that the pieces can be mounted to the legs. You will build one “U” shaped box and two “L” shaped boxes. Space the supports on the long aprons as indicated and secure with glue/screws. The drawer slide hardware will be mounted on the lower end of these supports in each drawer opening.  

Step 4
Step 5

 Cut and assemble the pieces for the drawer boxes. Attach 1/4” plywood to the bottom and secure with glue and brad nails. Attach the drawer slide hardware to the boxes but DO NOT attach the drawer faces until you have the drawers installed.

A quick and accurate way to line the faces up is to pre-drill the holes for the knobs or handles, line up the drawer face so it fits in the opening and put a screw through the holes into the drawer box. Pull the drawer out and fasten the face to the box from the inside. Finish drilling out the knob/handle holes.

Step 5
Step 6

 A view of how the drawer will look when the front is added. DO NOT add the drawer faces until the drawer is installed! See the previous step.

Step 6
Step 7

 Cut the legs to the height that you choose – 14-1/4” for a finished table height of 15”, 22-1/4” for a finished table height of 23”, or 29-1/4” for a finished table height of 30”. Attach to apron with screws through the pocket holes and angle brackets.

Step 7
Finishing Instructions

If painting, I like to sand the entire piece with 100 grit, then 220 grit, prime with any latex primer, sand again with 220 grit, and paint. Sanding the primer gives an extra-smooth finish! Finish with water-based polyurethane for added durability.

If staining, sand the entire piece with 60 grit, then 100 grit, then 220 grit. Stain as desired. For the finish, use wipe-on poly or brush-on poly.

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Note

If you enjoyed this post PLEASE STUMBLE IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date! You can now also: Follow my blog with blog lovin!

Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter