Feb
22
2012
Project Image

I'm really excited to dive into this collection! I'm all over the board these days on what I'm loving, but this console table is high on the list!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Hammer or Brad nailer
Lumber
  • 2 full sheets of ¾” plywood
  • 1 full sheet of ¼” lauan or hardboard
  • 8 – 1x2 at 8’
  • 1 – 1x3 at 6’
  • 1 – 1x3 at 4’
  • 2 – 1x6 at 8’
Materials
  • 1-1/4” screws
  • 1-1/4” pocket hole screws
  • 2” pocket hole screws
  • Small nails or 1-1/4” brads
  • 2 sets of 18” drawer slides
  • 4 – Drawer Handles or knobs
  • 2 - Hinges
  • Edge banding for the plywood top
  • Countersink bit for Drill
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 2 – 18-1/4” x 35-3/4” of ¾” plywood  - Sides
  • 1 - 18-1/4” x 68-1/2” of ¾” plywood – Bottom
  • 1 – 18-1/4” x 33-1/2” of ¾” plywood - Divider
  • 16 – 1x2 at 18-1/4” – Shelf & Drawer Slide Supports, Top Support
  • 1 – 18-1/4” x 22-3/4” of ¾” plywood – Shelf
  • 2 – 18-1/4” x 45” of ¾” plywood – Long Shelves
  • 2 – 1x2 at 35-3/4” – Frame Sides
  • 1 – 1x2 at 67” – Lower Frame Piece
  • 1 – 1x2 at 22-3/4” – Top Support
  • 1 – 1x2 at 45” – Top Support
  • 1 – 1x2 at 67” – Top Support
  • 1 – 1x2 at 22” – Shelf Trim
  • 1 – 1x2 at 31-1/4” – Shelf Trim
  • 2 – 1x2 at 43-1/2” – Shelf Trim
  • 1 – 35-3/4” x 70” of ¼” lauan or hardboard – Back
  • 1 – 20-1/4” x 72” of ¾” plywood – Top
  • 2 – 1x3 at 19-1/4” – Lower Trim
  • 1 – 1x3 at 71-1/2” – Front Lower Trim
  • 2 – 1x6 at 21” – Small Drawer
  • 2 – 1x6 at 42-1/2” – Long Drawer
  • 4 – 1x6 at 16-1/2” – Drawer Sides
  • 1 – 18” x 21” of ¼” lauan or hardboard – Small Drawer Bottom
  • 1 – 18” x 42-1/2” of ¼” lauan or hardboard – Long Drawer Bottom
  • 1 – 7-1/2” x 21-3/4” of ¾” plywood – Small Drawer Front
  • 1 – 6-1/2” x 43-1/4” of ¾” plywood – Long Drawer Front
  • 1 – 21-3/4” x 21-3/4” of ¾” plywood - Door
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Cut the pieces for the bottom, the sides, and four of the 1x2 supports. Secure two of the supports to the bottom of the sides with glue and countersunk 1-1/4” screws. Secure the other two supports to the bottom with countersunk 1-1/4” screws(make sure one of the supports is centered under the area where the divider will be placed), then attach the shelf to the side supports in the same manner.

Step 1
Step 2

Cut the piece for the divider. Set the Kreg jig for ¾” material and secure to the bottom with 2” pocket screws.

Step 2
Step 3

Cut the pieces for the shelf supports. Secure to the cabinet at the spacing indicated with glue and countersunk 1-1/4” screws.

Step 3
Step 4

Cut the pieces for the shelves. Attach two of the shelf supports to the underside of the long shelves with glue and countersunk 1-1/4” screws, then attach the shelves to the side supports in the same manner. Attach the smaller shelf in the same way, as well.

Cut the pieces for the drawer slide supports. Locate them as shown in the drawings. Attach them to the cabinet with glue and countersunk 1-1/4” screws.

Step 4
Step 4
Step 5

Cut the 1x2 pieces for the frame sides and bottom. Attach to the cabinet with glue and 1-1/4” brad nails. Make sure the top of the lower trim piece is flush with the top of the lower shelf.

Step 5
Step 6

Cut the three 1x2 pieces for the upper top supports. Using the Kreg jig, drill pocket holes in each end of the pieces. Secure to the cabinet with glue and 1-1/4” pocket hole screws as shown in the drawing.

Step 6
Step 7

Cut the pieces for the shelf trim pieces. Secure to the fronts of the shelves with glue and 1-1/4” brad nails, making sure the top of the trim is flush with the top of the shelves. The right side of the vertical trim will be flush with the smaller cabinet opening.

Cut the piece for the top support. Using the Kreg jig drill pocket holes in each end of the piece and secure to the cabinet with glue and 1-1/4” pocket hole screws as shown.

Step 7
Step 8

Cut the piece for the back and secure to the cabinet with glue and 1-1/4” brad nails. Place a few nails through the back into the shelf supports, also.

Step 8
Step 9

Cut the plywood piece for the top. Secure to the cabinet with glue and 1-1/4” brad nails through the top into the support pieces.

Step 9
Step 10

Cut the pieces for the lower trim. Mark and cut the arch in the front piece, if desired. Attach the side pieces first with glue and 1-1/4” brad nails, then attach the front piece in the same manner.

Step 10
Step 11

Cut the pieces for the drawer boxes. Assemble as shown with glue and 1-1/4” pocket hole screws. Attach the ¼” bottom pieces with glue and 1-1/4” brad nails. Do not attach the faces yet! Attach the drawer slides to the cabinet and drawer boxes according to the manufacturer’s directions locating them ¾” back from the face of the cabinet to allow for the front. Make any adjustments necessary.

Cut the pieces for the drawer fronts. Drill holes for handle or knob placement. Shim into place in the openings (there will be a 1/8” gap around all sides). Drill temporary screws through the holes for the handles into the drawer boxes. Open the drawers and fasten the fronts from the inside with 1-1/4” screws. Finish drilling out the holes for the handles.

Cut the piece for the door and drill a hole for the handle or knob location. Attach the hinges to the door and shim the door in place in the opening (there will be a 1/8” gap around all sides of the door, also). Attach the hinges to the cabinet.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Note

If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also: Follow my blog with blog lovin

I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!

Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter