Plans

Free DIY Furniture Plans to Build a Ballard Designs Inspired Morgan Table

03.20.12 By //
Project Image

A simple stylish build for your family room with plenty of space underneath for magazines or baskets!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Hammer or Brad nailer
Lumber
  • 1 – 2×2 at 8’
  • 4 – 1×2 at 6’
  • 2 – 1×3 at 6’
  • One sheet of ¾” plywood
Materials
  • 1-1/4” pocket hole screws
  • Small nails or 1-1/4” brads
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 4 – 2×2 at 17-1/4” – Legs
  • 2 – 1×3 at 38-1/4” – Long Aprons
  • 2 – 1×3 at 25-1/2” – Short Aprons
  • 2 – 1×2 at 38-1/4” – Long Shelf Support
  • 2 – 1×2 at 25-1/2” – Short Shelf Support
  • 1 – 1×2 at 26-1/2” – Center Support
  • 1 – 26-1/2” x 39-1/4” of ¾” plywood – Shelf
  • 1 – 28-1/2” x 41-1/4” of ¾” plywood – Top
  • 2 – 1×2 at 42-3/4” – Upper Trim
  • 2 – 1×2 at 28-1/2” – Upper Trim
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

Cut the pieces for the legs. Cut the taper as shown in the drawing.

Step 2
Step 2

Cut the aprons and the shelf supports as shown. Set the Kreg jig for ¾” material and drill pocket holes in each end of the pieces. The tapers on the legs will face to the outer sides. Attach the aprons to the legs with glue and 1-1/4” pocket hole screws. Locate them ¼” back from the outside face of the legs. Attach the shelf supports in the same manner, locating them ¼” back from the outside face of the legs, and also 4” up from the bottom of the leg.

Step 3
Step 3

Cut the piece for the center support. Drill pocket holes at each end and attach to the center of the long aprons.

Step 4
Step 4
Step 4

Cut the piece for the shelf. Cut ½” x ½” notches in each corner for the legs. Drill pocket holes in all sides and attach to the supports with 1-1/4” pocket hole screws. Locate the top of the shelf flush with the top of the supports.

Step 5
Step 5

Cut the piece for the top. Attach to the table frame with glue and 1-1/4” brad nails through the top, into the legs, aprons, and center support.

Step 6

Cut the pieces for the trim. The trim will for a ¾” lip around the top. Attach with glue and 1-1/4” brad nails.

If desired, a router and a decorative bit can be used to put a nice edge on the trim!

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also: Follow my blog with blog lovin!

I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.