Mar
12
2012
Project Image

A custom build designed by Matt himself! This cabinet is totally customizable – Matt used the actual measurements of his media components to determine the size of his cabinet. 

The Deets

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Hammer or Brad nailer
Lumber
  • 3 sheets of ¾” plywood
  • 1 sheet of ¼” lauan or hardboard
Materials
  • 1-1/2” pocket hole screws
  • Small nails or 1-1/4” brads
  • 4 – Drawer Handles or knobs
  • Edge banding for the plywood edges
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 1 – 18” x 93-1/2” – Top
  • 1 – 18” x 91-1/2” – Bottom
  • 6 – 18” x 22-3/4” – Dividers
  • 4 – 17” x 18” – Shelves
  • 2 – 18” x 18” – Shelves
  • 4 – 10” x 37-1/4” – Hutch Sides
  • 8 – 9” x 10” – Hutch Shelves
  • 1 – 10” x 80” – Hutch Top
  • 1 – 24-1/4” x 91-1/2” (1/4” plywood) - Back
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Apply edge banding, if desired, after each piece has been cut.

Cut the pieces for the top, bottom, and dividers. Set the Kreg jig for ¾” material and drill pocket holes in the 18” ends of the dividers. Attach one divider to each side of the bottom with glue and 1-1/2” pocket hole screws. Attach top in the same manner keeping in mind that each end of the top will overlap the sides by 1”. Check for square, then insert the remaining dividers at the spacing indicated in the drawing

Step 1
Step 2

Cut the pieces for the shelves and attach to the dividers with glue and 1-1/2” pocket hole screws.

Step 2
Step 2
Step 3

Cut the piece for the back and attach with glue and 1-1/4” brad nails.

Step 3
Step 4

Cut the pieces for the hutches. Attach the shelves to the sides with glue and 1-1/4” brad nails.

Set the hutch assemblies on the top spaced 59” apart. Attach the hutch top with glue and 1-1/4” brad nails, then secure the hutch assemblies to the cabinet with countersunk 1-1/4” screws.

Step 4
Step 4
Step 4
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Note

If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also: Follow my blog with blog lovin

I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!

Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter