Plans

Free DIY Furniture Plans to Build a PB Inspired Holman Wine Bottle Shelf

03.28.12 By //
Project Image

This rpoject makes two shelves, and is a fabulous and simple solution for all of those wine bottles you have stacked or stored on your counters…

Estimated Cost

Under $25

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Hammer or Brad nailer
Lumber
  • 1 – 1×6 at 6’
  • 1 – 1×10 at 4’
  • Or scraps of plywood measuring 8-1/2” wide by 24” long
Materials
  • Small nails or 1-1/4” brads
  • Edge banding if using plywood, optional
  • 1-1/4” hole saw or spade bit
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 2 – 1×6 at 24”, ripped down to 5” wide
  • 1 – 1×6 at 24” ripped to 4-1/2” wide
  • 2 – 1×10 at 24” ripped to 8-1/2” wide
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

Cut the piece for the front. Draw a line horizontally in the center of the board. Mark the spacing for the holes – 2” in from the end, six holes evenly spaced at 4” on center. Bore the holes part way through the board. Flip the board over to the back side, and finish boring the holes. This will keep the lumber from tearing out and splintering. Using the saw of your choice, cut the board in half down the horizontal line. You will have two boards with half-holes for your bottles!

Step 2
Step 2

Cut the pieces for the bottoms. Secure the fronts to the bottom edges with glue and 1-1/4” brads.

Step 3
Step 3

Cut the piece for the backs and secure to the bottom with glue and 1-1/4” brad nails.

To hang, locate and mark studs in the wall. Secure shelves to the wall by drilling countersunk 2-1/2” screws through the shelf into the studs.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also: Follow my blog with blog lovin!

I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

1 comment on “Free DIY Furniture Plans to Build a PB Inspired Holman Wine Bottle Shelf”

  1. Thank you so much for posting this as I’ve been wanting to buy it off of PB but couldn’t justify the price. Now that you have the plans listed, I can make 10 and feel so happy that I did it myself. Not to mention, my husband will be happy I didn’t spend 1k on PB wine holders. You ROCK!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.