Free DIY Furniture Plans to Build Pottery Barn Inspired Olivia Modular Components - Organizer
Free DIY Furniture Plans to Build Pottery Barn Inspired Olivia Modular Components - Organizer! We have the plans for the
bench and the lockers, and now the organizer yahoo!
Showcase: Built From These Plans
I am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!
Saw – Jig, Circular, or Miter
3 – 1x2 at 6’
1 – 1x3 at 6’
2 – 1x6 at 6’
1 sheets of ¾” plywood
1 half sheet of ¾” plywood
1-1/4” pocket hole screws
1-1/4” brad nails
Edge banding for plywood, if desired
2 – ¾” plywood at 14” x 15” – Sides
1 – ¾” plywood at 14” x 51-1/4” – Back
2 – ¾” plywood at 12-1/2” x 51-1/4” – Top & Bottom
3 – 1x2 at 12-1/2” – Bottom Supports
2 – 3/4” plywood at 11-3/4” x 12-1/2” – Dividers
2 – ¾” plywood at 12-1/2” x 16”- Shelves
3 – ½” plywood at 7-1/2” x 12-1/2”- Letter Dividers
2 – 1x2 at 51-1/4” – Front Aprons
3 – ¾” plywood at 11” x 14-1/4” – Drawer Bottoms
2 – 1x3 at 11” – Small Drawer Sides
2 – 1x3 at 15-3/4” – Small Drawer Front & Back
4 – 1x6 (ripped to 4-7/8” wide) at 11” – Large Drawer Sides
4 – 1x6 (ripped to 4-7/8” wide) at 15-3/4” – Large Drawer Front & Back
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the
GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Cut the pieces for the sides and the back. Set the Kreg jig for ¾” material and drill pocket holes in each end of the back. Attach the sides to the back using glue and 1-1/4” pocket hole screws.
Cut the piece for the bottom. Drill pocket holes in each end as well as one long edge. Position the bottom ¾” up from the bottom edge of the sides and back using glue and 1-1/4” pocket hole screws.
Cut the pieces for the bottom supports. Attach as shown using glue and countersunk 1-1/4” screws.
Cut the pieces for the dividers. Drill pocket holes in each end as well as one long edge. Attach as shown using glue and 1-1/4” pocket hole screws. The dividers will be ¾” shorter than the sides.
Cut the pieces for the shelves. Drill pocket holes in each end as well as the back edge. Attach as shown using glue and 1-1/4” pocket hole screws.
Cut the pieces for the letter dividers. Attach using glue and 1-1/4” brad nails through the bottom into the dividers as well as through the shelf into the dividers.
Cut the piece for the top. Drill pocket holes in each end. Attach to the sides using glue and 1-1/4” pocket hole screws. Also use pocket hole screws through the holes in the top of the dividers into the underside of the top.
Cut the pieces for the front aprons. Attach to the front using glue and 1-1/4” brad nails or 1-1/4” countersunk screws.
Cut the pieces for the drawer boxes. Drill pocket holes in each end of the side pieces as well as all four edges of the bottoms. Attach the sides to the bottoms using glue and 1-1/4” pocket hole screws. Attach the front and back using glue and 1-1/4” pocket hole screws. There are no drawer slides so to make the drawers slide easily in the openings, apply a coat of paste wax to the bottom of the drawer as well as on each shelf.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.