Plans

Free DIY Furniture Plans to Build a Pottery Barn Inspired Modular Family Lockers

01.15.13 By //
Project Image

Free DIY Furniture Plans to Build a Pottery Barn Inspired Modular Family Lockers

***Single locker requires 2 sheets of plywood. If building two lockers, a total of three sheets will be required (there will be enough of the second sheet left over to create parts for the second locker).***

You can see above how these pieces will work together once you build a few! Any configuration you want will be fabulous!!!

Estimated Cost

$75-100

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
Lumber
  • Scrap of 1×4 at 14-1/2”
  • 2 full sheets of ¾”plywood
Materials
  • 1-1/4” pocket hole screws
  • Edge banding for plywood, optional
  • One set of hinges
  • Cabinet pull or handle
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  2 – ¾” plywood at 15” x 67-3/4” – Sides
  • 1 – ¾” plywood at 14-1/2” x 15” – Bottom
  • 1 – ¾” plywood at 14-1/2” x 63-1/2” – Back
  • 1 – ¾” plywood at 15” x 16” – Top
  • 1 – 1×4 at 14-1/2” – Kick Plate
  • 3 – ¾” plywood at 13-1/2” x 14-1/2” – Shelves
  • 1 – ¾” plywood at 14-1/4” x 63-1/4” – Door
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site. Always make sure you buy easy to assemble furniture

Step 1
Step 1

 If using edge banding, it will need to be applied before assembly.

Cut the pieces for the sides and the back. Set the Kreg jig for ¾” material and drill pocket holes in the top edges of the sides, as well as the longer edges of the bottom. Position as shown and attach using glue and 1-1/4” pocket hole screws.

Step 2
Step 2

Cut the pieces for the back. Drill pocket holes in all four edges. Position as shown then secure to the sides and bottom using glue and 1-1/4” pocket hole screws.

Step 3
Step 3
Step 3

Cut the piece for the top. Attach to the sides and back using glue and 1-1/4” pocket hole screws through the holes in the sides and back into the underside of the top.

Cut the piece for the kick plate. Drill pocket holes in each end as well as one long edge. Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 4
Step 4

Cut the pieces for the shelves. Drill pocket hole in each end. The shelves will be positioned ¾” back from the front edge. Secure using glue and 1-1/4” pocket hole screws.

Step 5
Step 5

Cut the piece for the door. There will be a 1/8” gap around all sides of the door in the opening. Install the hinges on the door, then attach to the cabinet. Install the cabinet pull or handle.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.