• Essentials from Target for The Design Confidential Feeling Fall // Essentials for Creating a Cozy Mantel
  • Free DIY Furniture Plans // How to Build an Indoor Outdoor House Bed Playhouse + Outdoor Daybed Lounge
  • Family Room Sneak Peek / The Design Confidential in Collaboration with Joss and Main for a Curators Collection Sale Story Interview
  • Hammock and Lounging Area for the Home Depot Style Challenge Outdoor Games Edition
  • DIY Faux Watercolor Wallpaper Wall Treatment with Paint
  • Free DIY Furniture Plans // How to Build a Tri Trestle Table
  • DIY Home Decor // How To Make Your Own Removable Wallpaper
Mar
24
2013
Project Image

Free DIY Furniture Plans to Build a Design Workshop Deep Drawer Component! These components are designed to work with steel shelving standards and brackets similar to these where screws can be inserted through the bottom of the bracket into the component.

The Deets

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig 
Lumber
  • One half sheet of ¾” plywood
Materials
  • 1-1/4” pocket hole screws
  • Edge banding for plywood, optional
  • Screws to go through the bracket into the component – length will vary
  • One set of 16” drawer slides
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  2 – ¾” plywood at 17-1/4” x 31” – Top & Bottom
  • 2 – ¾” plywood at 14-1/4” x 17-1/4” – Sides
  • 1 – ¾” plywood at 14-1/4” x 29-1/2” – Back
  • 1 – ¾” plywood at 16” x 27” – Drawer Bottom
  • 2 – ¾” plywood at 14” x 16” – Drawer Sides
  • 1 – ¾” plywood at 14” x 29-1/4” – Drawer Front
  • 1 – ¾” plywood at 14” x 28-1/2” – Drawer Back
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

If using edge banding, it will be applied to the exposed edges of the plywood before assembly.

Cut the pieces for the bottom and sides. Set the Kreg jig for ¾” material and drill pocket holes in the top and bottom edges of the side pieces. Attach to the bottom as shown using glue and 1-1/4” pocket hole screws.

Step 1
Step 2

Cut the piece for the back. Drill pocket holes in all four edges. Secure to the sides and back using glue and 1-1/4” pocket hole screws.

Step 2
Step 3

Cut the piece for the top. Secure using glue and 1-1/4” pocket hole screws through the pocket holes in the sides and the back.

Step 3
Step 4

Cut the piece for the drawer front. Cut the notch as shown using a jigsaw. Cut the pieces for the sides, bottom, and back. Drill pocket holes in each end of the sides as well as all four edges of the bottom. Assemble as shown using glue and 1-1/4” pocket hole screws. The front will overlap the drawer box by 3/8” on each side. Install the drawer slide hardware according to the manufacturer’s instructions. For an easy tutorial, click here. Make any necessary adjustments. The box will be placed on the shelving brackets then secured with screws through the bracket into the box.

Step 4
Step 4
Step 4
Step 4
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter