Plans

Free DIY Furniture Plans to Build a Jacqueline Bedside Table

04.03.13 By //
Project Image

Free DIY Furniture Plans to Build a Jacqueline Bedside Table. Oh this little lady is gorgeous, isn’t she? I love the delicate curves paired with her substantial form. A fabulous addition to any room! Xx…Rayan

Estimated Cost

$50-$75

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Countersink Bit for Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad Nailer
Lumber
  • 2 – 2×2 at6’
  • 2 – 1×2 at 6’
  • 2 – 1×6 at 6’
  • 2 – 3/8” thick craft boards at 2-1/2” wide x 3’
  • Half sheet of ¾” plywood
  • Half sheet of ½” plywood
Materials
  • 1” pocket hole screws
  • 1-1/4” pocket hole screws
  • 3/4” screws
  • 1-1/4” brad nails
  • 1 – Set of 20” Drawer slides
  • 1 – Drawer pull
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 4 – 2×2 at 29-1/4” – Legs
  • 2 – 1×2 at 19-1/2” – Side Stretchers
  • 2 – 1×6 ay 19-1/2” – Sides
  • 3 – 1×2 at 31-1/2” – Front & Back Stretchers
  • 1 – 1×6 at 31-1/2” – Back
  • 2 – 3/8” material at 2-1/2” x 19-1/2” – Slide Fillers
  • 1 – ¾” plywood at 23” x 35-1/2” – Top
  • 1 – ¾” plywood at 19-1/4” x 29” – Drawer Bottom
  • 2 – ¾” plywood at 3-3/4” x 19-1/4” – Drawer Sides
  • 1 – ¾” plywood at 3-3/4” x 30-1/2” – Drawer Back
  • 1 – ¾” plywood at 3-3/4” x 31=1/4” – Drawer Front
  • 2 – ½” plywood at 6-1/4” x 20” – Hutch Sides
  • 1 – ½” plywood at 6-1/4” x 34-1/2” – Hutch Back
  • 4 – ½” plywood at 2-1/2” x 8-1/2” – Hutch Dividers
  • 1 – ½” plywood at 8-1/2” x 34-1/2” – Hutch Shelf
  • 1 – ¾” plywood at 8-1/2” x 34-1/2” – Hutch Top
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

Cut the pieces for the legs, stretchers,  and sides. Set the Kreg jig for ¾” material and drill pocket holes in each end of the side and stretcher pieces. Center on the legs, then attach using glue and 1-1/4” pocket hole screws.

Step 2
Step 2

Cut the pieces for the back and back stretcher. Drill pocket holes in each end. Center on the legs, then attach using glue and 1-1/4” pocket hole screws.

Step 3
Step 3
Step 3

Cut the pieces for the stretchers and drill pocket holes in each end. Position as shown, then attach using glue and 1-1/4” pocket hole screws.

Cut the pieces for the drawer slide fillers. Attach to the sides as shown using countersunk ¾” screws.

Step 4
Step 4

Cut the piece for the top. Attach using glue and 1-1/4” brad nails through the top into the sides, legs, back, and stretchers.

Step 5
Step 5
Step 5

Cut the pieces for the drawer box. Drill pocket holes on all four edges of the bottom, as well as each end of the drawer sides. Attach the sides to the bottom as shown using glue and 1-1/4” pocket hole screws. Attach the drawer back in the same manner. The drawer front will overlap the sides of the drawer box by 3/8” at each side. Attach using glue and 1-1/4” pocket hole screws. Install the drawer slides according to the manufacturer’s instructions. For an easy tutorial, click here. Make any necessary adjustments.

Step 6
Step 6
Step 6

Cut the pieces for the hutch sides. Cut an arc in each piece maintaining the dimensions as shown. Set the Kreg jig for ½” material and drill pocket holes in the lower edge of each piece. Keep in mind there will be a right and a left piece.

Cut the piece for the hutch back and drill pocket holes in each end, as well as the bottom edge. Attach using glue and 1” pocket hole screws.

Step 7
Step 7

Cut the pieces for the hutch dividers. Drill pocket holes in one edge only of each piece. Position two of the dividers and shown then secure using glue and 1” pocket hole screws. Set the other two dividers aside.

Step 8
Step 8
Step 8

Cut the piece for the hutch shelf. Attach to the sides and dividers using glue and 1-1/4” brad nails through the top into the dividers, as well as through the sides into the shelf.

Attach the other two dividers as shown using glue and 1” pocket hole screws.

Step 9
Step 9

Cut the piece for the top. Attach using glue and 1-1/4” brad nails through the top into the dividers, and through the sides and back into the shelf.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.