Plans

Free DIY Furniture Plans to Build a Moreno Bar

05.06.13 By //
Project Image

Free DIY Furniture Plans to Build a Moreno Bar! This plan is perfect for those of you who would like to bring a little of that entertaining vibe into your room! Xx… Rayan

Estimated Cost

$75-$100

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Countersink bit for drill
  • Square
  • Sander
  • Kreg Jig
  • Brad nailer
Lumber
  • 1 – 1×2 at 6’
  • 2 – 1×3 at 8’
  • 3 – 1×4 at 8’
  • 1 – 2’ x 2’ sheet of ¼” plywood, lauan, or hardboard
  • 1 – half sheet of ¾” plywood
  • 1 – full sheet of ¾” plywood
Materials
  • 1-1/4” pocket hole screws
  • 1-1/4” screws
  • 1-1/4” brad nails
  • 1” brad nails
  • Edge banding for the plywood
  • 1 set of 16” drawer slides
  • 3 – Cabinet pulls
  • 2 sets of hinges for the doors
  • 1 set of hinges for the flip-up top
  • 2 Friction Lid Supports (like these)
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 4 – 1×4 (ripped to 2-3/4” wide) at 33-1/4” – Side Legs
  • 2 – ¾” plywood at 10-3/4” x 30-3/4” plywood – Side Panels
  • 2 – 1×4 at 29-3/4” – Front Legs
  • 1 – 1×4 at 45” – Front Stretcher
  • 1 – ¾” plywood at 34-3/4” x 43-1/2” – Back
  • 3 – ¾” plywood at 15-1/2” x 43-1/2” – Shelves
  • 1 – 1×3 at 27-1/4” – Front Divider
  • 1 – 1×4 (ripped to 2-3/4” wide) at 15-1/2” – Top Divider
  • 1 – ¾” plywood at 12-1/8” x 16-3/4” – Fixed Top
  • 1 – ¾” plywood at 16-5/8” x 33-3/4” – Flip-Up Top
  • 4 – 1×3 at 12-1/2” – Door Frame
  • 4 – 1×3 at 27-1/8” – Door Frame
  • 2 – ¾” plywood at 12-1/2” x 22-1/8” – Door Panel
  • 2 – 1×2 at 14-1/2” – Drawer Box Sides
  • 2 – 1×2 at 9-1/2” – Drawer Front & Back
  • 1 – ¼” plywood, lauan, or hardboard at 9-1/2” x 16” – Drawer Bottom
  • 1 – 1×3 at 11” – Drawer Front
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

If using edge banding, it will be applied to the exposed edges of the plywood before assembly.

Cut the pieces for the side legs and the side panel. Cut the angle in the leg using a jigsaw. Set the Kreg jig for ¾” material and drill pocket holes in each long end of the panel, and in one long edge of one leg as shown. Keep in mind, there will be a right side assembly and a left side assembly! Attach the legs to the panels using glue and 1-1/4” pocket hole screws.

Step 2
Step 2

Cut the pieces for the front legs and the front stretcher. Cut the angle in the legs using a jigsaw, and drill pocket holes in the top edge keeping in mind there will be a right and a left. Cut the hole in the stretcher for the drawer using a jigsaw. Attach the legs to each end of the stretcher using glue and 1-1/4” pocket hole screws, then attach the side panels using glue and 1-1/4” pocket hole screws through the holes drilled in the side legs.

Step 3
Step 3

Cut the piece for the back. Draw a 4” radius at each corner and cut with a jigsaw. Drill pocket holes in each side edge. Secure the back piece to the sides using glue and 1-1/4” pocket hole screws. The back will stand 4” above the side to create a “backsplash”.

Step 4
Step 4

Cut the pieces for the shelves and drill pocket holes in three edges. Secure to the cabinet as shown using glue and 1-1/4” pocket hole screws. The bottom of the upper shelf will be flush with the bottom of the upper stretcher.

Step 5
Step 5
Step 5

Cut the piece for the front divider and drill pocket holes in the top edge. Secure to the upper stretcher as shown. Add a couple of countersunk 1-1/4” screws through the divider into each of the shelves.

Cut the piece for the top divider and drill pocket holes in each end. Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 6
Step 6

Cut the piece for the fixed top. Position the piece so that it butts up against the backsplash and overhangs the front and side by ½”. Secure in place using glue and 1-1/4” brad nails.

Cut the piece for the flip-up top and install the hinges. There will be a 1/8” gap between the top and the back splash as well as between the top and the fixed top. The front and sides will overhang by ½”.

Step 7
Step 7
Step 7

Cut the pieces for the doors and drill pocket holes as shown. Install the hinges, then install the doors. Attach the cabinet pulls in the location desired.

Step 8
Step 8
Step 8
Step 8

Cut the pieces for the drawer. Drill pocket holes in each end of the side pieces, and assemble the frame using glue and 1-1/4” pocket hole screws. Attach the bottom using glue and 1” brad nails. Install the drawer slides according to the manufacturer’s instructions. For an easy tutorial, click here. Make any necessary adjustments.

Cut the piece for the drawer front. For another easy tutorial, click here. Install the cabinet pull as desired.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.