Plans

Free DIY Furniture Plans to Build an Indoor Outdoor Antigua Round Table

07.03.13 By //
Project Image

Free DIY Furniture Plans to Build an Indoor Outdoo Antigua Round Table. Technically inspired by an outdoor design, I personally think it would be smashing in any eat in area inside too! Xx… Rayan

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad Nailer
Lumber
  • 2 – 2×2 at 8’
  • 2 – 2×3 at 8’
  • 1 – 2×4 at 8’
  • 1 sheet of ¾” plywood
Materials
  • 2-1/2” pocket hole screws
  • 2-1/2” screws
  • 1-1/4” brad nails
  • 1-1/2” wide edge banding
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 1 – 4×4 post at 28-1/2” – Center Post
  • 2 – ¾” plywood at 48” in diameter – Table Top
  • 4 – 2×4 at 18” – Feet
  • 4 – 2×3 at 27” – Supports
  • 8 – 2×2 at 19-13/16” – Angled Supports
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

 Cut the pieces for the center post and the table top. Spread glue on one piece of the plywood for the top and position the second piece on it. Wiggle the second piece to create suction, then clamp and secure the pieces using 1-1/4” brad nails. Set the Kreg jig for 1-1/2” material and drill pocket holes in two opposing sides of one end of the post. Center on the table top then secure using glue and 2-1/2” pocket holes in each side.

Step 2
Step 2

 Cut the pieces for the feet and drill pocket holes in one end of each piece. Secure to the bottom of the post with glue and 2-1/2” pocket hole screws.

Step 3
Step 3

 Cut the pieces for the 2×3 supports and drill pocket holes in each end. Position on the feet as shown then secure using glue and 2-1/2” pocket hole screws. Secure the supports to the underside of the table top also.

Step 4
Step 4
Step 4

 Cut the pieces for the angled supports. Cut the angles as shown in the drawings noting that they are NOT cut at 45 degrees. Secure the supports to the underside of the table, the center post, and the feet using glue and 2-1/2” toenailed screws.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.