Plans

Free DIY Furniture Plans: How to Build an Oslo 3 Drawer Dresser

01.08.14 By //

Free DIY Furniture Plans: How to Build an Oslo 3 Drawer Dresser. I’m going through a phase in my current design sensibilities that longs for a simplified style of furniture and decor, with a bit of a nod to the past and our design roots as a global society. I am loving pieces like this dresser that aren’t fussy and will still stand the test of time with clean lines and minimal detailing. It helps that this fabulous combo also packs a light punch to the old wallet and remains both relatively easy to build and low in cost. Are you craving a more streamlined lifestyle right now too? I wonder if it’s the season or time of year… Xx… Rayan

Estimated Cost

$75-$100

Dimensions
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Countersink Bit for Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad Nailer
Lumber
  • 3 – 1×2 at 6’
  • 3 – 1×10 at 6’
  • 2 – 1×10 at 8’
  • 1 – 2×2 at 4’
  • 2 sheets of ¾” plywood
Materials
  • 1-1/4” pocket hole screws
  • 2-1/2” screws
  • 1-1/4” brad nails
  • 3 sets of 16” drawer slides
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 1 – ¾” plywood at 17” x 34-1/2” – Bottom
  • 2 – 1×2 at 17” – Bottom Frame
  • 2 – 1×2 at 36” – Bottom Frame
  • 4 – 2×2 at 4-3/4” – Legs
  • 2 – ¾” plywood at 17-3/4” x 34-1/4” – Sides
  • 1 – ¾” plywood at 34-1/4” x 34-1/2” – Back
  • 2 – 1×2 at 34-1/2” – Stretchers
  • 1 – ¾” plywood at 18-1/2” x 36” – Top
  • 3 – ¾” plywood at 14-1/2” x 32” – Drawer Bottoms
  • 6 – 1×10 at 14-1/2” – Drawer Box Sides
  • 6 – 1×10 at 33-1/2” – Drawer Box Front & Back
  • 3 – ¾” plywood at 11-1/4” x 36” – Drawer Fronts
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Cut the pieces for the bottom panel and the bottom frame. Set the Kreg jig for ¾” material and drill pocket hole in each end of the shorter 1×2 frame pieces as well as all four edges of the bottom panel. Assemble the panel as shown using glue and 1-1/4” pocket hole screws. Insert the panel then secure using glue and 1-1/4” pocket hole screws. The top face of the panel will be flush with the top edge of the frame.

Step 2

Cut the pieces for the legs. Position them on the underside of the bottom snug against the frame in each corner. Secure using glue and countersunk 2-1/2” screws through the bottom into the legs.

Step 3

Cut the pieces for the sides and drill pocket holes in the top and bottom edges. Secure to the bottom frame locating them ¾” back from the front edge of the bottom frame.

Step 4

Cut the piece for the back and drill pocket holes in all four edges of the panel. Secure to the sides and bottom using glue and 1-1/4” pocket hole screws.

Step 5

Cut the pieces for the stretchers and drill pocket holes in each end. Secure to the sides as shown using glue and 1-1/4” pocket hole screws.

Cut the piece for the top. The front and sides will overhang by ½”. Secure using glue and 1-1/4” pocket hole screws through the sides and back.

Step 7

Cut the pieces for the drawer boxes. Drill pocket holes in all four edges of the bottom as well as each end of the sides. Assemble the drawer box as shown using glue and 1-1/4” pocket hole screws. Install the drawer slides according to the manufacturer’s installation instructions, locating them ¾” back from the front edge of the sides. For an easy tutorial, click here. Make any necessary adjustments.

Step 8

Cut the pieces for the drawer fronts. Mark the position for the drawer pulls and drill the holes. Starting with the bottom drawer front, position it with a 1/8” gap at the bottom then drive screws through the holes for the drawer pulls into the drawer box. Open the drawer, and secure the drawer front using countersunk 1-1/4” screws from the inside. Position the next drawer fronts in the same manner with a 1/8” gap between them and secure the same way. Remove the screws from the holes for the drawer pull then finish drilling the holes. Install the drawer pull. For an easy tutorial on installing drawer fronts, click here.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.