Jan
23
2013
Project Image
Project Details

Free DIY Furniture Plans to Build a Pottery Barn Inspired Modular Family Cube. Perfect with the other pieces in the Modular Family collection!!!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig 
Lumber
  • Scrap of 1x4 at 14-1/2”
  • 1 full sheet of ¾”plywood
Materials
  • 1-1/4” pocket hole screws
  • Edge banding for plywood, optional
  • One set of hinges
  • Cabinet pull or handle
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 2 – ¾” plywood at 15” x 22-1/4” – Sides
  • 1 – ¾” plywood at 14-1/2” x 15” – Bottom
  • 1 – ¾” plywood at 14-1/2” x 18” – Back
  • 1 – ¾” plywood at 15” x 16” – Top
  • 1 – 1x4 at 14-1/2” – Kick Plate
  • 1 – ¾” plywood at 14-1/4” x 17-3/4” - Door
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

If using edge banding, it will need to be applied before assembly.

Cut the pieces for the sides and the back. Set the Kreg jig for ¾” material and drill pocket holes in the top edges of the sides, as well as the longer edges of the bottom. Position as shown and attach using glue and 1-1/4” pocket hole screws.

Step 1
Step 2

Cut the pieces for the back. Drill pocket holes in all four edges. Position as shown then secure to the sides and bottom using glue and 1-1/4” pocket hole screws.

Step 2
Step 3

Cut the piece for the top. Attach to the sides and back using glue and 1-1/4” pocket hole screws through the holes in the sides and back into the underside of the top.

Cut the piece for the kick plate. Drill pocket holes in each end as well as one long edge. Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 3
Step 3
Step 4

Cut the piece for the door. There will be a 1/8” gap around all sides of the door in the opening. Install the hinges on the door, then attach to the cabinet. Install the cabinet pull or handle.

Step 4
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Knock Offs 
Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Jan
21
2013
Project Image
Project Details

Free DIY Furniture Plans to Build a Pottery Barn Inspired Modular Family Bridge. Yay, moving right along through this collection! We already covered the bench and lockers for this modular family, and today the bridge!

The Deets

Of course the whole collection can be configured any way you like...

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$25-$50

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad nailer
Lumber
  • 1 full sheet of ¾”plywood
Materials
  • 1-1/4” pocket hole screws
  • 1-1/4” brad nails
  • Edge banding for plywood, optional
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  2 – ¾” plywood at 15” x 47-1/2” – Top & Bottom
  • 2 – ¾” plywood at 13-1/2” x 15” – Sides
  • 1 – ¾” plywood at 13-1/2” x 47-1/2” – Back
  • 2 – ¾” plywood at 14-1/4” x 46” – Divider Box Top & Bottom
  • 3 – ¾” plywood at 12” x 14-1/4” - Dividers
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

If using edge banding, it will need to be applied before assembly.

Cut the pieces for the box. Set the Kreg jig for ¾” material and drill pocket holes in the top and bottom edges of the sides. Assemble as shown and attach the sides using glue and 1-1/4” pocket hole screws.

Step 1
Step 2

Cut the piece for the back. Drill pocket holes in all four edges. Position as shown then secure to the sides, top, and bottom using glue and 1-1/4” pocket hole screws.

Step 2
Step 3

Cut the pieces for the divider box. Drill pocket holes in each end of the shorter dividers. Position as shown and secure to the top and bottom using glue and 1-1/4” pocket hole screws.

Insert the divider box into the bridge box and secure using 1-1/4” brad nails.

Step 3
Step 3
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Knock Offs 
Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Jan
18
2013
Project Image
Project Details

Free DIY Furniture Plans to Build a Pottery Barn Inspired Modular Family Bench. We covered the plans for the locker unit here, and now the bench! You can see down below how this lovely modular family actually looks when it's all completed!!! It's fab, right?

The Deets

Pretty cool, eh?

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$50-$75

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad nailer
Lumber
  • 1 - 1x2 at 3’
  • 2 – 1x6 at 8’
  • 1 full sheet of ¾”plywood
Materials
  • 1-1/4” pocket hole screws
  • 1-1/4” screws
  • 1-1/4” brad nails
  • Edge banding for plywood, optional
  • One pair of 16” drawer slides
  • Cabinet knob or pull
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  2 – ¾” plywood at 20” x 35-1/2” – Sides
  • 2 – 1x2 at 16-3/4” – Seat Supports
  • 1 – 1x6 at 45-1/2”- Back Stretcher
  • 1 – ¾” plywood at 18-3/4” x 45-1/2” – Seat
  • 1 – ¾” plywood at 16-3/4” x 45-1/2” – Back
  • 2 – 1x6 at 11-3/4” – Front Aprons
  • 2 – 1x6 at 16-3/4” – Drawer Supports
  • 1 – ¾” plywood at 16” x 19-1/2” – Drawer Bottom
  • 2 – 1x6 (ripped to 5-3/8” wide) at 16” – Drawer Sides
  • 1 – 1x6 (ripped to 5-3/8” wide) at 21” – Drawer Back
  • 1 – 1x6 (ripped to 5-3/8” wide) at 21-3/4” – Drawer Front
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

If using edge banding, it will need to be applied before assembly.

Cut the pieces for the sides. Maintain the dimensions as shown when cutting the curves. The curve at the back is optional and can be made by drawing a line 1” in from the back edge, marking the center of that line, then drawing lines from the center to the back corners. Cut out with a jigsaw.

Cut the pieces for the seat supports. Position as shown and secure using glue and 1-1/4” countersunk screws.

Step 1
Step 2

Cut the piece for the back stretcher. Set the Kreg jig for ¾” material and drill pocket holes in each end. Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 2
Step 3

Cut the piece for the seat. The front of the seat will overlap by ½”. Secure to the supports and back stretcher using glue and 1-1/4” brad nails or countersunk screws.

Step 3
Step 4

Cut the piece for the back. Drill pocket holes in each end as well as one long edge as show. Position the back so it rests on the seat and secure using glue and 1-1/4” pocket hole screws.

Step 4
Step 5

Cut the pieces for the front aprons and drawer supports. Drill pocket holes in one end of each apron pieces, as well as each end of the drawer supports. Assemble as shown, then attach to the sides and back stretcher using glue and 1-1/4” pocket hole screws.

Step 5
Step 6

Cut the pieces for the drawers. Drill pocket holes in each end of the side pieces as well as all four edges of the bottom. Assemble as shown using glue and 1-1/4" pocket hole screws. The fronts will overlap the drawer box by 3/8" on each side.

Install the drawer slides according to the manufacturer's instructions. For an easy tutorial, click here. Make any necessary adjustments. 

Attach the cabinet pull or handle if desired.

Step 6
Step 6
Step 6
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Knock Offs 
Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Jan
15
2013
Project Image
Project Details

Free DIY Furniture Plans to Build a Pottery Barn Inspired Modular Family Lockers

***Single locker requires 2 sheets of plywood. If building two lockers, a total of three sheets will be required (there will be enough of the second sheet left over to create parts for the second locker).***

The Deets

You can see above how these pieces will work together once you build a few! Any configuration you want will be fabulous!!!

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost

$75-100

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig 
Lumber
  • Scrap of 1x4 at 14-1/2”
  • 2 full sheets of ¾”plywood
Materials
  • 1-1/4” pocket hole screws
  • Edge banding for plywood, optional
  • One set of hinges
  • Cabinet pull or handle
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  2 – ¾” plywood at 15” x 67-3/4” – Sides
  • 1 – ¾” plywood at 14-1/2” x 15” – Bottom
  • 1 – ¾” plywood at 14-1/2” x 63-1/2” – Back
  • 1 – ¾” plywood at 15” x 16” – Top
  • 1 – 1x4 at 14-1/2” – Kick Plate
  • 3 – ¾” plywood at 13-1/2” x 14-1/2” – Shelves
  • 1 – ¾” plywood at 14-1/4” x 63-1/4” - Door
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site. Always make sure you buy easy to assemble furniture

Step 1

 If using edge banding, it will need to be applied before assembly.

Cut the pieces for the sides and the back. Set the Kreg jig for ¾” material and drill pocket holes in the top edges of the sides, as well as the longer edges of the bottom. Position as shown and attach using glue and 1-1/4” pocket hole screws.

Step 1
Step 2

Cut the pieces for the back. Drill pocket holes in all four edges. Position as shown then secure to the sides and bottom using glue and 1-1/4” pocket hole screws.

Step 2
Step 3

Cut the piece for the top. Attach to the sides and back using glue and 1-1/4” pocket hole screws through the holes in the sides and back into the underside of the top.

Cut the piece for the kick plate. Drill pocket holes in each end as well as one long edge. Position as shown and secure using glue and 1-1/4” pocket hole screws.

Step 3
Step 3
Step 4

Cut the pieces for the shelves. Drill pocket hole in each end. The shelves will be positioned ¾” back from the front edge. Secure using glue and 1-1/4” pocket hole screws. 

Step 4
Step 5

Cut the piece for the door. There will be a 1/8” gap around all sides of the door in the opening. Install the hinges on the door, then attach to the cabinet. Install the cabinet pull or handle.

Step 5
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Knock Offs 
Disclaimer

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

drupal counter