• Essentials from Target for The Design Confidential Feeling Fall // Essentials for Creating a Cozy Mantel
  • Free DIY Furniture Plans // How to Build an Indoor Outdoor House Bed Playhouse + Outdoor Daybed Lounge
  • Family Room Sneak Peek / The Design Confidential in Collaboration with Joss and Main for a Curators Collection Sale Story Interview
  • Hammock and Lounging Area for the Home Depot Style Challenge Outdoor Games Edition
  • DIY Faux Watercolor Wallpaper Wall Treatment with Paint
  • Free DIY Furniture Plans // How to Build a Tri Trestle Table
  • DIY Home Decor // How To Make Your Own Removable Wallpaper

Browse all Free Woodworking Plans that Require a Kreg Jig

Oct
21
2014
The Design Confidential Reader Showcase PotteryBarn Inspired Picnic Table and Modified Benches

I modified the benches to make stools. They work great. The plans were very easy to follow and it looks awesome in the backyard...just in time for the winter, haha.

Estimated Cost 

About $60 for the stools and $50-60 for the table.

Length of Time 

Approx 3 days...took me longer because I couldnt do it all at one time. :)

Lumber Used 

White Pine

Finishing Technique 

Thompsons Waterseal

Close Up of The Design Confidential Reader Showcase PotteryBarn Inspired Picnic Table and Modified Benches
Full Finished Shot of The Design Confidential Reader Showcase PotteryBarn Inspired Picnic Table and Modified Benches
Oct
20
2014
The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Project Details

By special reader request, this media console is so very handsome and wants to live in your home... So go forth and build this beautiful baby and make your home that much more stylish! 

The Deets
Finished Build of The Design Confidential Free DIY Furniture Plans to Build a Marin Media Consol

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost
$150-$250
Dimensions
Dimensions for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Tools
Lumber
  • 1 – 2x4 at 8’
  • 7 – 1x2 at 8’
  • 3 – 3/4” plywood at – 4’x8’
Materials
Cut List
  • 2 – 3/4” plywood at 18”x19-1/4” – Cabinet Sides
  • 2 – 3/4” plywood at 19-1/4”x56” – Cabinet Top and Bottom
  • 4 – 2x4 at 6” – Legs
  • 1 – 3/4” plywood at 16-1/2”x56” – Cabinet Back
  • 1 – 3/4” plywood at 16-1/2”x18” – Center Divider
  • 1 – 3/4” plywood at 18”x37-1/4” – Left Shelf
  • 1 – 3/4” plywood at 18”x18” – Right Shelf
  • 6 – 1x2 at 16” – Door Tops and Bottoms
  • 6 – 1x2 at 18” – Door Sides
  • 27 – 1x2 at 15” – Door Slats
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Click on Images to expand! 

Step 1

Cut the pieces for the Sides, Top, and Bottom. Apply edge banding to front edges of all pieces, if desired. Set the Kreg Jig for 3/4” material and drill pocket holes in the ends of the Top and Bottom pieces. Make sure the pocket holes will face the inside of the Console. Assemble pieces as shown with glue and 1-1/4” pocket screws.

Build the Cabinet Box for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Step 2

Cut the pieces for the Legs. You will need 4 of these exactly the same. This diagram shows you how to mark out the shape you need for the Console Legs. Use your circular saw to cut this out. If you simply connect the dots between the dimensions outlined below and use a circular saw to make these cuts, you won't have to worry about the actual angle for each corner.

Attach Legs to the bottom of the Console as shown with glue and 1-3/4” wood screws. The Legs should be placed 3/4” from the Sides of the Console and flush with the front edge of the Console. Insert the wood screws down through the Console Bottom into the Legs so that the screws are hidden. Also, make sure that the screws are countersunk so that they do not interfere with items placed inside the Console.

Leg Pattern for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Leg Location for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Step 3

Cut the piece for the Back. Drill pocket holes in each edge of the Back. Attach the Back as shown with glue and 1-1/4” pocket screws. Make sure that the pocket holes face the inside of the Console.

Cut the piece for the Center Divider. Drill pocket holes in the top and bottom of the Divider. Assemble as shown with glue and 1-1/4” pocket screws.

Back for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Center Divider for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Step 4

Cut the pieces for the Shelves. Drill pocket holes in the ends of the shelves and assemble as shown with glue and 1-1/4” pocket screws. There will be an approximate 1/2” space in the back between the shelves and the Console Back.

Shelves for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Step 5

Cut the pieces for the Door Tops, Bottoms, and Slats. Drill pocket holes in the ends of the Tops, Bottoms, and Slats. Attach as shown with glue and 1-1/4” pocket screws. There will be a 1/4” gap between each Slat. Repeat this for all three Doors. Remember to keep checking for “square” on each door – each door should measure the same diagonally in both directions.

Door Frame for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Door Construction for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Step 6

Attach hinges as shown at the top and bottom of the Doors and attach to the Console. There will be a 1/4” space between each installed Door. Add Door hardware such as a pull or knob if desired.

Hinge Placement for The Design Confidential Free DIY Furniture Plans to Build a Marin Media Console
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

If painting, I like to sand the entire piece with 100 grit, then 220 grit, prime with any latex primer, sand again with 220 grit, and paint. Sanding the primer gives an extra-smooth finish! Finish with water-based polyurethane for added durability.

If staining, sand the entire piece with 60 grit, then 100 grit, and then 220 grit. Stain as desired. For the finish, use wipe-on poly or brush-on poly.

Disclaimer

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. // Post May Contain Affiliate Links

Oct
09
2014
Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Project Details

The Low Loft Bunk Bed Series is hands down our most popular series of project plans to date. Many of you have asked for a queen sized version of this fabulous sleeper and I am finally obliging! Yahoo. I have made a modification to the ladder in this plan, for both the orientation as well as the method of construction, to be more accomodating to adults and to allow for a more compact footprint.

The Deets
Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost
$150-$250
Dimensions
Dimensions for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Tools
Lumber
  • 4 - 4x4 at 6' Fence Posts - UNTREATED
  • 2 - 2x6 at 8'
  • 2 - 2x6 at 6'
  • 14 - 2x4 at 8'
  • 15 - 1x4 at 6' - if 8' boards are cheaper, buy those - you will have leftover scrap.
Materials
Cut List
  • 4 - 4x4 at 59" - Legs
  • 2 - 2x6 at 81" - Side Rails
  • 2 - 2x6 at 70" - Head / Foot Rails
  • 2 - 2x4 at 81" - Cleats
  • 4 - 2x4 at 81" - Upper Side Rails and Center Support Joists
  • 4 - 2x4 at 70" - Upper Head / Foot Rails
  • 1 - 2x4 at 59" - Front Guard Rai Ladder Leg
  • 4 - 2x4 at 8 3/4" - Lower Front Guard Rail Ladder Supports
  • 1 - 2x4 at 18" - Upper Front Guard Rail Ladder Supports
  • 2 - 2x4 at 55" - Guard Rail Side Upper Rails
  • 4 - 2x4 at 27" - Ladder Rungs
  • 15 - 1x4 at 67" - Slats
Instructions

**I recommend finishing your boards and posts prior to assembling and simply touching up later. This will make for easier painting and will keep you from having to paint this wherever this piece will actually live (bedroom) since you will have to assemble it in the area it will be placed (at 45 or more inches wide this will not fit through a doorway after it's assembled).

** This plan is designed to accomodate a Queen Sized Mattress at 66" x 80". If your mattress is a different size, you will need to adjust for this by adding or subtracting length to all pieces on the side you are adjusting. For example if your mattress is 68" wide then you will add 2" inches to every single width running dimension on the plans below (Head/Foot pieces). 

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Cut all 4 Legs to size and then notch out the sections shown in the image on one of the legs. You can use a jig saw, table saw or a circular saw to do this. Then attach the Cleats to the Side Rails using 2" Screws and be sure the bottom of the Side Rail and the Cleat are flush. You 

To attach the Rails to the Legs you will arrange the pieces as shown in the diagram below, making sure to leave 1 1/2" on either side of the ends of the Rails to allow for the Head and Foot Rails later. Clamp together making sure everything is completely square before you proceed. Once square and aligned as needed, you will use a 7/16" Drill Bit and drill through all 3 pieces on each side (the leg, rail and cleat), creating 2 holes on either side for the bolts that will secure this. 

Fasten with your Carriage Bolts and tighten.

Leg Dimensions and Side Rails for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Step 2

Attach the Bed Rail Hardware to the Side Rails. You can secure the Lower Head and Foot Rails to the Legs using your Kreg Jig set for 1 1/2" material and your 2 1/2" pocket hole screws.

** Be sure you place your pocket holes in a location that doesn't interfere with the bed rail hardware. The Head and Foot Rails will sit flush with the outside of the Legs and with the Lower Side Rails. You can also skip pocket holes and use 3" Screws to secure these to the Side Rails if you prefer.

Use your Kreg Jig set for 1 1/2" material, to secure the Center Support Joists to the Head and Foot Rails with 2 1/2" Pocket Hole Screws. Then fasten the Upper Side Rails on one side of your bed (not the side that will have your ladder) to the Back Legs using 3" Screws. 

Upper Side Rails and Support Joists for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Step 3

Create your Guard Rail Leg Unit. This will be 2 - 2x4's, one long and the other cut into sections with spacing and dimensions as shown in the image. This will hold your ladder rungs later so just be sure that the separation between your shorter ladder supports will actually fit a 2x4 nice and snug. You need to fit it in place but you don't want any wiglle room so a tight fit is better than a slightly loose fit. Attach the Front Upper Side Rails to the Leg using 3" screws and attach to the Guard Rail Leg Unit using 2" Screws. 

Guard Rail Side Rails and Ladder Legs for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Step 4

Attach the Upper Head Rails on the side opposite where you choose to put the ladder, in my example this would be the left side. Use 3" Screws and secure into the ends of the Upper Side Rails. 

Upper Head Rails for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Step 5

Lay your Slats approximately 2" apart. Be sure the 2 on the outside edges are flush in both corners. Screw down using 1 1/4" Screws or Nails and fasten to both cleats and both support joists. 

Bed Slats for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Step 6

Attach the remaining 2 upper Foot Rails to the Back Upper Side Rails and the Front Leg using a Pocket hole System (Kreg Jig) set for 1 1/2" materials and 2 1/2" pocket hole screws and glue to fasten the Rails to the front Leg. To fasten the Foot Rails to the Back Side you can either use Pocket Hole Screws and glue to connect them to the Back Leg or 3" Wood Screws and Glue, with a countersink bit to predrill and secure directly to the end of the Upper Side Rails. 

Slide the Ladder Rungs into place and secure with glue. You can choose to secure with 3" Wood Screws from the legs into the ends of the rungs, but this is optional and you can absolutely secure with glue and call it a day! 

Ladder Rungs and Upper Foot Rails for Free DIY Furniture Plans // How to Build a Queen Sized Low Loft Bunk Bed
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

Disclaimer

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. // Post May Contain Affiliate Links

Oct
02
2014
The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table

I am new to building furniture and I am so very thankful for these plans. Saved me a lot of money.

So I am got married in June and was walking through Pottery Barn with her one day when she said how much she loved a certain Pottery Barn Table. The Toscana Table is a beautiful table but no way I was going to spend what they are asking for it. I blurted out that I could build that, mind you I had 0 building experience and had no idea where to even start. So, after Google sleuthing for a few days I came accross this website and these plans. They were absolutely a life savor. I did modify it though. I used 2x6's for the legs instead iof 2x4's. It gave a thicker look and I felt matched the Pottery Barn version more closely. Also, the skirt, instead of have the 2x4's being vertical, I laid them flat. The reasoning behind this is that my fiance is 6'2'' and I am 6'3'', wanted a little more room for our legs. This adjustment also allowed me to extend the table top past the legs a bit more. For the stain I used General Finishes Java Gel Stain. You will not find a better stain for your money. It was so easy to work with and the end result was a beautiful rich color. The top coat I used was Min-Wax High Build Polyurethane. I am very pleased with the results and I am so very thankful for these building plans. I discovered a hobby that I love and can't wait to build something else now.

Building the Legs for The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table
Attaching the Center Joist for The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table
Estimated Cost 

$100-$200

Length of Time 

2 weekends, about 32 hours

Lumber Used 

All Pine

Building the Support Frame for The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table
Angle Progress Shot for The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table
Legs and Side View for The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table
Finished Shot of The Design Confidential Reader Showcase // Pottery Barn inspired Toscana Table
Oct
01
2014
Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Project Details

I love a good chest of drawers, and when that dresser has stylish drawers... well that is simply my fave! I hope enjoy these Free DIY Furniture Plans and Instructions on How to Build a Vodder Chest of Drawers! If you need a little storage in your life, this is definitely a good one! Xx... Rayan

The Deets
Finished Chest for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers

Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!

Estimated Cost
$75-$125
Dimensions
Dimensions for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Tools
Lumber
  • 1 – 2x4 at 8’
  • 1 – 3/4” plywood at – 4’x8’
  • 1 – 1/2” plywood at – 4’x8’
Materials
Cut List
  • 2 – 3/4” plywood at 14-1/2”x33” – Chest Sides
  • 2 – 3/4” plywood at 14-1/2”x26” – Chest Top and Bottom
  • 1 – 3/4” plywood at 26”x31-1/2” – Chest Back
  • 4 – 2x4 at 5” – Legs
  • 10 – 3/4” plywood at 1”x12” – Drawer Guides
  • 6 – 1/2” plywood at 11-1/2”x24-1/2” – Drawer Bottoms
  • 12 – 1/2” plywood at 4”x11-1/2” – Drawer Sides
  • 6 – 1/2” plywood at 3-1/2”x24-1/2” – Drawer Backs
  • 6 – 1/2” plywood at 5”x25-1/2” – Plain Drawer Fronts
  • 6 – 1/2” plywood at 5”x25-1/2” – Bowtie Drawer Fronts
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Cut the pieces for the Sides, Top, and Bottom. Apply edge banding to front edges of all pieces, if desired. Set the Kreg jig for 3/4” material and drill pocket holes in the ends of the Top and Bottom pieces. Make sure the pocket holes will face the inside of the Chest. Assemble pieces as shown with glue and 1-1/4” pocket hole screws.

Chest Frame for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 2

Cut the piece for the Back. Drill pocket screws in each edge of the Back. Attach the back as shown with glue and 1-1/4” pocket screws. Make sure that the pocket holes face the inside of the Chest.

Back for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 3

Cut out the Legs as shown.

Leg for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 4

Attach Legs to the bottom of the Chest as shown with glue and 1-1/2” wood screws. The Legs should be placed 2” from the edges of the Chest and at a 45-degree angle. Insert the wood screws down through the Chest Bottom into the Legs so that the screws are hidden. Also, make sure that the screws are countersunk so that they do not interfere with the Drawer.

Attach Legs for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 5

Cut the pieces for the Drawer Guides. Assemble as shown with glue and 1-1/4” wood screws. Insert the wood screws from the inside of the Chest, through the Drawer Guides, into the Chest Sides so that the screws are hidden. The Guides will be 1-1/2” set back from the front of the Chest, and have approximately a 1/4” gap in the back.

Drawer Guides for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 6

Cut the pieces for the Drawer Sides, Bottoms, Backs, and Plain Fronts for all Drawers. Set the Kreg jig for 1/2” material and drill pocket holes in the ends of the underside of the Bottoms and on the outside front ends of the Sides. Attach as shown with glue and 1” pocket screws.

Drill pocket holes in the sides and bottoms of the Drawer Backs. Attach as shown with glue and 1” pocket hole screws.

 

Drawer Bottom and Sides for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Drawer Back for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 7

For Drawers 1 through 5, attach the Plain Fronts as shown with glue and 1” pocket screws. The top of the Plain Fronts for Drawers 1 through 5 will extend 3/4” above the Sides.  The bottoms of the Plain Fronts will extend 1/4” below the Sides.

Drawer Plain Front for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 8

Next, cut out the Bowtie Fronts for Drawers 1 through 6 as shown. Attach to the Plain Fronts of Drawers 1 through 5 with glue and 3/4” brad nails. The Bowtie Fronts will line up exactly with the Plain Fronts.

Drawer Bowtie for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Attach Drawer Bowtie for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 9

For Drawer 6, attach the Plain Front as shown with glue and 1” pocket hole screws. The bottom of the Plain Front will be even with the Sides, and the top of the Plain Front will extend 1” above the Sides.

Attach the Bowtie Front as shown with glue and 3/4” brad nails.

Tip: Paint the fronts and tops of the Plain Drawer Fronts in black or another accent color to add a really cool effect to this piece.

After sanding, staining, and sealing, you may want to apply a coat of paste wax to the bottoms of the Drawers and tops of the Drawer Guides to help them slide smoothly. Add drawer hardware such as a pull or knob if desired.

Drawer 6 Plain Front for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Drawer 6 Front for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Step 10

Insert Drawers 1 through 6 into Chest and fill them up with all of your goodies!

Insert Drawers for Free DIY Furniture Plans // How to Build a Vodder Chest of Drawers
Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School.

If painting, I like to sand the entire piece with 100 grit, then 220 grit, prime with any latex primer, sand again with 220 grit, and paint. Sanding the primer gives an extra-smooth finish! Finish with water-based polyurethane for added durability.

If staining, sand the entire piece with 60 grit, then 100 grit, and then 220 grit. Stain as desired. For the finish, use wipe-on poly or brush-on poly.

Disclaimer

// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. // Post May Contain Affiliate Links

Sep
25
2014
The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches

Wonderful set of plans. Easy to follow. Easy to modify if you need to, as I did in my case. Results are very pleasing.

Estimated Cost 

Eh, about $175, give or take

Length of Time 

About 4 Weekends plus a little after work a few nights for sanding and staining.

Modifications 

Well, there are a couple....

1. I don't like that the crossing legs on both the benches and the table were actually cut in half and attached. Therefore, I cut dado cuts into both cross pieces, glued and screwed them together for added stability.

2. My wife is an Italian and likes to have big meals with lots of peeps. Therefore, I modified the plans to push the table and benches to 8ft long rather than the original plan which is 6ft. I used a little flair in the center of the table to add the additional 2ft and break up the long lines that 8ft boards would have created. In doing so, I had to add some additional bracing on the underside to make it a bit more sturdy to support the extra length. But I didn't have to add a center support leg system.

Lumber Used 

Douglas Fur

Finishing Technique 

I used the same finish as the builder John because I like the way his photos turned out. I was not disappointed in the least. Two coats of Behr transparent weatherproofing all in one finish. Cedar natural tone

Beautiful Sides for The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches
Close Up of Table Top for The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches
Finished Build and Stain for The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches
Opposite Side of The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches
Fish Eye Wide Angle for The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches
Table Top for The Design Confidential Reader Showcase // Tahoe-Dude's Chesapeake Picnic Pable and Benches
drupal counter