Plans

Free Woodworking Plans to Build a 2×2 Collection Double Sided Daybed

07.25.10 By //
Project Image

This bed is so simple to construct, you will be done in no time! It’s also extremely easy on the budget…I see no reason why this couldn’t be add to an amazing seating area outdoors as well! If you use outdoor fabric on your pillows or a mattress cover, you will be in business!

Estimated Cost

$25-$50

Tools
  • Tape Measure
  • Square
  • Sander
  • Drill
  • Saw
Lumber
  • 7 – 2×3 at 8′
  • 1 – 2×2 at 6′
  • 3 – 1×3 at 10′
  • 1 – 1×3 at 8′
  • 2 – 1×2 at 8′
Materials
  • 3″ Screws
  • 2 1/2″ Screws
  • 2″ Screws
  • Wood Glue **if you would like this to be taken apart at any point, do not use glue.
  • Wood Filler or Paintable Silicone Sealant if being used outside and painted.
  • Finishing Supplies or Sealant for outdoor use.
Cut List
  • 5 – 2×3 at 25 1/2″ (Legs)
  • 2 – 2×3 at 75 1/2″ (Front and Back Rails)
  • 4 – 2×3 at 34 1/2″ (Stretchers)
  • 2 – 1×2 at 75 1/2″ (Cleats)
  • 2 – 1×3 at 39″ (End Aprons)
  • 9 – 1×3 at 36″ (Supports)
  • 1 – 2×3 at 72″ (Front Apron)
  • 2 – 2×3 at 37 1/4″ (Back Apron)
  • 2 – 2×3 at 40 1/2″ (Arm Rest)
  • 2 – 2×2 at 38 1/2″ (Back Rest)
Instructions

Notes: If you are making this for outdoor use, purchase wood that holds up well to weather and moisture. This might include Cedar, Redwood, and Teak , but I would ask your local lumber supply for appropriate wood species for your area and climate. You should Finish and Seal all boards prior to assembling if this is for outdoor use. This will keep it water tight and protected. You can likely get away with using a different wood if you finish and seal all pieces really well. **Always Pre-Drill and Counter Sink for the most professional appearance. Check for Square after every step.

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

Attach the Rails to the Legs: Use 2 1/2″ Screws and Wood Glue. Place the bottom of the rails 4″ from the bottom of the legs (top of the rails will fall at 6 1/2″ from the ground).

Step 2
Step 2

First attach the Stretchers to the Cleats: Use 3″” Screws and Wood Glue. Then Attach the Cleats to the Frame Rails: Use 2″ Screws and Wood Glue.

Step 3
Step 3

Attach the End Aprons: Use 2″ Screws and Wood Glue

Step 4
Step 4

Lay the Slats approximately 6″ Apart and screw in place using 1 1/4″ Screws. Do not glue the slats if you plan to remove them at any point.

Step 5
Step 5

Attach the Back Rests (Green), then attach the Arm Rests (Red). Use 3″ Screws and Wood Glue. Then attach the Front and Back Aprons: Use 2 1/2″ Screws and Wood Glue.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

4 comments on “Free Woodworking Plans to Build a 2×2 Collection Double Sided Daybed”

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.