Plans

Free DIY Furniture Plans to Build a Ballard Designs Inspired Paulette Server

02.28.12 By //
Project Image

This project is quite the beauty. Strong traditional style and amazing functionality, this fine piece of work is sure to serve any need for storage and display you might have, or might even think of having! 

Estimated Cost 

$75-$100

Dimensions 
Dimensions for This Project

Tools 
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
  • Hammer or Brad nailer
Lumber 
  • 2 Full Sheets of ¾” plywood
  • 1 Sheet of ¼” lauan or hardboard
  • 4 – 1×2 at 8’
  • 1 – 1×4 at 4’ or scrap at least 25” long
  • 1 – 1×6 at 4’ or scrap at least 25” long
Materials 
  • 1-1/4” pocket hole screws
  • 1-1/4” screws
  • Small nails or 1-1/4” brads
  • 3 sets of 16” drawer slides
  • Drawer Handles or knobs
  • Shelf pins (for adjustable shelves)
  • Edge banding for the plywood
  • Countersink bit for Drill
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List 
  • 2 – 17-1/4” x 35” of ¾” plywood – Console Sides
  • 6 – 1×2 at 17-1/4” – Shelf Supports
  • 1 – 1×2 at 26-1/2” – Back Spacer
  • 3 – 17-1/4” x 26-1/2” of ¾” plywood – Console Shelves
  • 3 – 1×2 at 25” – Console Frame
  • 1 – 1×4 at 25” (ripped to 3-1/4” wide) – Console Frame
  • 2 – 1×2 at 35” – Console Frame
  • 1 – 28” x 35” of ¼” lauan or hardboard – Back
  • 1 – 18-3/4” x 28” of ¾” plywood – Console Top
  • 2 – 11-1/4” x 47-1/4” of ¾” plywood – Hutch Sides
  • 2 – 11-1/4” x 26-1/2” of ¾” plywood – Hutch Shelves, Fixed
  • 2 – 11-1/4” x 26-1/4” of ¾” plywood – Hutch Shelves, Adjustable
  • 1 – 1×6 at 25” – Hutch Frame
  • 2 – 1×2 at 25” – Hutch Frame
  • 2 – 1×2 at 47-1/4” – Hutch Frame
  • 1 – 28” x 47-1/4” of ¼” lauan or hardboard – Hutch Back
  • 1 – 13-3/4” x 28” of ¾” plywood – Hutch Top
  • 4 – 9-1/2” x 24” of ¾” plywood – Large Drawer Boxes
  • 4 – 9-1/4” x 14-1/2” of ¾” plywood – Large Drawer Boxes
  • 4 – 2-3/4” x 24” of ¾” plywood – Small Console  & Hutch Drawer Boxes
  • 2 – 2-3/4” x 14-1/2” of ¾” plywood – Small Console Drawer Box
  • 2 – 2-3/4” x 8” of ¾” plywood – Small Hutch Drawer Box
  • 3 – 16” x 24” of ¼” lauan or hardboard – Drawer Box Bottoms
  • 1 – 8” x 24” of ¼” lauan or hardboard – Drawer Box Bottom
  • 2 – 11-1/2” x 24-3/4” of ¾” plywood – Large Drawer Fronts
  • 2 – 3-1/2” x 24-3/4” of ¾” plywood – Small Drawer Fronts
  • 2 – 28” Baseboard Trim or Door Casing – Upper and Lower Trim
Instructions 

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1

Step 1 

Cut the pieces for the console sides, shelf supports and back spacer. Set the Kreg jig for ¾” material and drill pocket holes in each end of the back spacer only. Attach the supports to the sides as indicated in the drawing with glue and countersunk 1-1/4” screws. Attach the back spacer as indicated with glue and 1-1/4” pocket hole screws.

Step 2

Step 2 

Cut the pieces for the shelves.  Attach to the underside of the supports with glue and countersunk 1-1/4” screws.

Step 3

Step 3 

Cut the piece for the back and attach to the console with glue and 1-1/4” brad nails.

Step 4
Step 4

Step 4 

Cut the pieces for the console frame. Drill pocket holes in the ends of the horizontal boards and assemble the frame as indicated in the drawing with glue and 1-1/4” pocket hole screws. The horizontal pieces of the frame will be flush with the tops of the shelves.

Attach the frame to the console with glue and 1-1/4” brad nails.

 

Step 5

Step 5 

Cut the piece for the console top. Apply edge banding, if desired, and attach to the console with glue and 1-1/4” brad nails through the top into the sides, back spacer, and frame.

Step 6

Cut the pieces for the hutch sides. Drill pocket holes in one short end of each piece to attach to the console. Also, drill two rows of holes on each piece for the adjustable shelves and shelf pins. Attach the sides to the console with 1-1/4” pocket hole screws making sure the outside faces are flush with the sides of the console.

Step 7

Step 7 

Cut the pieces for the fixed shelves and apply edge banding, if desired. Attach to the hutch sides as indicated with glue and 1-1/4” pocket hole screws. It will be easier to attach the bottom shelf first, then the upper shelf. The bottom shelf will be located ¾” up from the top of the console.

Cut the pieces for the adjustable shelves. They will be ¼” shorter than the fixed shelves. Apply edge banding to the front of the shelves, if desired.

Step 8

Step 8 

Cut the piece for the hutch back and attach with glue and 1-1/4” brad nails.

Step 9
Step 9

Step 9 

Cut the pieces for the hutch frame. Using a jigsaw, cut the arc in the 1×6 piece as shown. Drill pocket holes in each end of the horizontal pieces and assemble the frame as indicated with glue and 1-1/4” pocket hole screws.

Attach the frame to the hutch with glue and 1-1/4” brad nails. 

Step 10

Step 10 

Cut the piece for the hutch top. Apply edge banding, if desired, and attach to the hutch with glue and 1-1/4” brad nails through the top into the sides and frame.

Step 11 

Cut the pieces for the upper and lower trim. Attach as indicated with glue and 1-1/4” brad nails.

Step 12 

Cut the pieces for the drawer boxes. Set the Kreg jig for ¾” material and drill pocket holes in each end of the shorter pieces. Attach the bottom with glue and brad nails. Do not attach the drawer faces until the drawer  boxes have been installed and adjusted! Install the drawer slides in the console (the hutch drawer will not have drawer slides) according to the manufacturer’s instructions placing them ¾” back from the opening face to allow for the fronts. Make any adjustments necessary.

Cut the pieces for the drawer fronts. Drill the holes for the handle or knob placement. Shim in place in the opening (there will be a 1/8” gap around all sides) and drill a temporary screw through the holes into the drawer boxes. Open the drawers and secure the fronts to the boxes from the insides with 1-1/4” screws. Finish drilling out the holes for the handle or knob.

Finishing Instructions 

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also: Follow my blog with blog lovin

I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.