Plans

Free DIY Furniture Plans to Build a RH Inspired Maison Bed (King)

05.14.12 By //
Project Image

We have plans for the queen size, and now for the king!

Estimated Cost

$50-$75

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Square
  • Sander
  • Kreg Jig
Lumber
  • 7 – 2×2 at 6’
  • 2 – 2×2 at 8’
  • 2 – 2×4 at 8’
  • 8 – 1×3 at 6’
  • One sheet of ¾” plywood
Materials
  • 2” pocket hole screws
  • 1-1/4” screws
  • 4 – Furniture legs at least 8” tall
  • Nailhead upholstery trim  and nails (go here)
  • Countersink bit for Drill
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  • 2 – 2×2 at 51-1/2” – Headboard Sides
  • 4 – 2×2 at 78”” – Headboard & Footboard
  • 1 – 2×2 at 81” – Headboard
  • 2 – 2×4 at 80-1/2” – Side Rail Bottoms
  • 2 – 2×2 at 6” – Side Rail Ends
  • 2 – 2×2 at 82” – Side Rail Tops
  • 8 – 1×3 at 78” – Slats
  • 1 – ¾” plywood at 31-7/8” x 77-7/8” – Headboard Panel
  • 2 – ¾” plywood at 4-3/8” x 80-3/8” – Side Panels
  • 1 – ¾” plywood at 4-3/8” x 77-7/8” – Foot Panel
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

Cut the pieces for the headboard. Set the Kreg jig for 1-1/2” material and drill pocket holes in one end of each of the pieces for the sides, and in both ends of the lower piece. Assemble as shown with glue and 2” pocket hole screws.

Step 2
Step 2

Cut the pieces for the lower rails. Drill two pocket holes in each end of these boards. Attach to the headboard as shown using the outer pocket hole only but DO NOT use glue! You may want to disassemble it someday!

Step 3
Step 3

Cut the piece for the lower headboard rail. Drill pocket holes in each end. Attach as shown with glue (it’s ok on this piece!) and 2” pocket hole screws, also with a screw through the lower rail into this piece.

Step 4
Step 4

Cut the pieces for the side rail ends. Assemble as shown in the drawing with the pocket holes facing to the inside. Use glue and ONE pocket hole screw.

Step 5
Step 5

Cut the pieces for the top of the side rail. Drill pocket holes in one end of each piece. Assemble as shown with the pocket holes facing down and the screws secured into the headboard. DO NOT use glue at this joint but you can use glue to attach this piece at the end.

Step 6

Cut the pieces for the footboard. Drill two pocket holes in each end of the piece that will be used for the top only. Secure to the side rail end pieces but DO NOT use glue. Secure the lower piece with a screw through the remaining pocket hole in the lower side rail and again, DO NOT use glue!

Attach the feet or legs.

Step 7
Step 7

**The bed will need to be stained or painted before inserting the slats or upholstery panels.**

Cut the pieces for the slats and attach to the lower rail with countersunk 1-1/2” screws.

Step 8
Step 8

Cut the panels for the headboard, footboard, and side rails. Set the Kreg jig for ¾” material and drill pocket holes in the back side to attach to the frames. They will be upholstered as follows:

Cover the front each panel with a thin piece of foam, then cover the front with upholstery batting. Lay the fabric over the top and secure at the edge of each panel with the upholstery nail strips. Trim the fabric leaving at least 1-1/2” of fabric around the edges of the panels (this will be hidden when the panels are inserted into the frames and secured.). Insert the panels into each of the openings and attach with 2” pocket hole screws.

When disassembling the bed, the panels will not have to be removed. For the footboard, only remove the screws attaching this piece to the side rails. For the side rails, only remove the screws attaching the panels and sides to the headboard. Nothing will have to be removed for the headboard.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!

You can now also: Follow my blog with blog lovin!

I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.