Free DIY Furniture Plans to Build a West Elm Inspired Emmerson Buffet
Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!
- Tape Measure
- Saw – Jig, Circular, or Miter
- Countersink Bit for Drill
- Kreg Jig
- Brad Nailer
- 2 – 1×3 at 6’
- 1 – 1×6 at 3’
- Two sheets of ¾” plywood
- 1-1/4” pocket hole screws
- Edge banding for plywood, optional
- Two sets of hinges
- Two door handles or pulls
- Wood filler
- Wood glue
- Finishing Supplies
- 2 – 1×6 at 13-3/4” – Base
- 1 – ¾” plywood at 17-3/4” x 53-1/2” – Bottom
- 2 – 1×3 at 48” – Base Stretchers
- 2 – ¾” plywood at 17-3/4” x 25-3/4” – Sides
- 1 – ¾” plywood at 25-3/4” x 52” – Back
- 1 – ¾” plywood at 17” x 25-3/4” – Divider
- 1 – ¾” plywood at 17-3/4” x 53-1/2”- Top
- 2 – ¾” plywood at 17” x 17” – Shorter Shelves
- 2 – ¾” plywood at 16-1/4” x 34-1/4” – Longer Shelves
- 3 – ¾” plywood at 16-15/16” x 25-1/2” – Doors
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Edge banding should be applied to all exposed edges of plywood before assembly.
Cut the pieces for the base and the bottom. Set the Kreg jig for ¾” material and drill pocket holes along one long edge of each base piece. Attach to the bottom as shown using glue and 1-1/4” pocket hole screws.
Cut the pieces for the base stretchers. Drill pocket holes in each end as well as one long edge of each piece. Attach to the bottom and base pieces as shown using glue and 1-1/4” pocket hole screws.
Cut the pieces for the sides. Drill pocket holes as shown. Attach to the bottom using glue and 1-1/4” pocket hole screws.
Cut the piece for the back. Drill pocket holes as shown. Attach to the bottom and sides using glue and 1-1/4” pocket hole screws.
Cut the piece for the divider. Drill pocket holes as shown. Attach to the bottom and back using glue and 1-1/4” pocket hole screws.
Cut the piece for the top. Attach using glue and 1-1/4”pocket hole screws through the holes in the sides, back, and divider into the top.
Cut the pieces for the shelves. Drill pocket holes in each end as well as one long edge of each piece. Attach as shown using glue and 1-1/4” pocket hole screws.
Cut the pieces for the doors. There will be a 1/8” gap around all sides as well as the center. Install the hinges, then install the doors. Drill holes and attach any door hardware.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.