Plans

Free DIY Furniture Plans to Build a Wisteria Inspired Recycled Pine Console

02.13.13 By //
Project Image

Free DIY Furniture Plans to Build a Wisteria Inspired Recycled Pine Console!!!

Psst… I would love your support and a vote in the final round of The Homies…. Homie! Pretty Pretty Please… it means a lot to this little bloggy poo! It you don’t already have an account at Apartment Therapy you will need to register but it only takes like 3 seconds and you can immediately pop over to the voting page (Best Home Project & DIY Blog) and click The Design Confidential. Seriously it’s so easy and fast and means so very very much to us and the success of this site. Pretty Please Xx…Rayan

Estimated Cost

$50-$75

Dimensions
Dimensions for This Project
Tools
  • Tape Measure
  • Saw – Jig, Circular, or Miter
  • Drill
  • Countersink Bit for Drill
  • Square
  • Sander
  • Kreg Jig
  • Brad nailer
Lumber
  • 1 – 4×4 at 8’
  • 4 – 1×2 at 6’
  • 4 – 1×3 at 8’
  • 2 – 2×2 at 8’
  • 4 – 2×4 at 8’
  • One sheet of ¾” plywood
Materials
  • 1-1/4” pocket hole screws
  • 2-1/2” pocket hole screws
  • 1-1/4” screws
  • 1-1/4” brad nails
  • Edge banding for plywood
  • 4 – 5” casters
  • 8 – angle brackets for edges, optional
  • Wood filler
  • Sandpaper
  • Wood glue
  • Finishing Supplies
Cut List
  •  4 – 4×4 at 22-1/4” – Legs
  • 6 – 2×4 at 10-1/2” – Side Frames
  • 6 – 2×4 at 51-1/2” – Stretchers
  • 4 – 1×2 at 51-1/2” – Slat Supports
  • 34 – 1×3 at 10-1/2” – Slats
  • 4 – 2×2 at 13-11/16” – X
  • 8 – 2×2 at 6-1/8” – X
  • 1 – ¾” plywood at 17-1/2” x 58-1/2” – Top
Instructions

Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.

Step 1
Step 1

Cut the pieces for the legs and the side frames. Set the Kreg jig for 1-1/2” material and drill pocket holes in each end of the frame pieces. Attach to the legs as shown using glue and 2-1/2” pocket hole screws.

Step 2
Step 2

Cut the pieces for the stretchers. Drill pocket holes in each end. Secure to the legs as shown using glue and 2-1/2” pocket hole screws.

Step 3
Step 3

Cut the pieces for the slat supports. Set the Kreg jig for ¾” material and drill pocket holes along one long edge of each piece. Attach to the middle and lower stretchers using glue and 1-1/4” pocket hole screws, making sure the bottom face is flush with the bottom face of the stretchers.

Step 4
Step 4

Cut the pieces for the slats. Attach to the supports using glue and countersunk 1-1/4” screws. There will be ½” spacing between each piece.

Step 5
Step 5
Step 5
Step 5

Cut the pieces for the X. Cut the angles as shown – they are NOT 45 deg angles! Draw a line at the measurement shown, then draw another line from the corner of the board to the opposite end of the line in order to make the angle.  Set the Kreg jig for 1-1/2” material and drill pocket holes in the straight edges of the shorter pieces. Maintain the dimensions shown in drawing 2 and secure using glue and 2-1/2” pocket hole screws.

Attach the X using toenailed brad nails through the X into the stretcher.

Step 6

Cut the piece for the top. Secure using glue and 1-1/4” brad nails. Add the angle brackets to the upper and lower edges, if desired.

Attach the casters according to the manufacturer’s instructions.

Finishing Instructions

Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School

**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.

Print Friendly, PDF & Email

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.