Free DIY Furniture Plans to Build a Full Sized Stria Bed! Another fabulous bed for the Stria Collection of pieces and a wonderful size for those rooms needing something larger than a twin but not quite as large as a queen. This bed would be perfect along with our Free DIY Furniture Plans to Build a West Elm Inspired Stria 3-Drawer Dresser or the Free DIY Furniture Plans to Build a West Elm Inspired Stria 6-Drawer Dresser. Xx… Rayan
- Tape Measure
- Saw – Jig, Circular, or Miter
- Countersink Bit for Drill
- Kreg Jig
- Brad Nailer
- 2 – 2×2 at 6’
- 2 – 1×2 at 8’
- 4 – 1×2 at 6’
- One sheet of ¾” plywood
- 2 – 1×4 at 8’
- 15 – 1×3 at 6’
- One sheet of ¼” plywood
- 1-1/2” pocket hole screws
- 1-1/4” screws
- 5/8” brad nails
- Surface mounted keyhole bed rail brackets (like these)
- Wood filler
- Wood glue
- Finishing Supplies
- 2 – 2×2 at 18” – Footboard Legs
- 2 – 2×2 at 50” – Headboard Legs
- 4 – 1×2 at 53” – Headboard & Footboard Frames
- 1 – ¾” plywood at 4-1/2” x 53” – Footboard Panel
- 1 – ¾” plywood at 36-1/2” x 53” – Headboard Panel
- 2 – 1×4 at 78” – Sides
- 2 – 1×2 at 75” – Slat Supports
- 15 – 1×3 at 54-1/2” – Slats
- 18 – ¼” plywood at 1-1/2” x 54-1/2” – Trim Slats
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Cut the pieces for the legs and headboard/footboard frames. Set the Kreg jig for ¾” material and drill pocket holes in each end of the frame pieces. Attach to the legs using glue and 1-1/2” pocket hole screws as shown in the drawings.
Cut the pieces for the headboard/footboard panels. Drill pocket holes as shown. Attach to the frames using glue and 1-1/2” pocket hole screws. The faces of the panels will be flush with the faces of the frames.
Cut the pieces for the sides and slat supports. Attach the slat supports to the sides using glue and countersunk 1-1/4” screws. The bottom of the supports will be flush with the bottom of the sides. Attach the bed hardware according to the manufacturer’s instructions.
Cut the pieces for the slats. Attach to the supports using countersunk 1-1/4” screws. Do not use glue!
Cut the pieces for the trim slats. Attach to the headboard and footboard as shown with approximately ½” spacing using glue and 5/8” brad nails.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.