Free DIY Furniture Plans to Build a Pottery Barn Inspired Ava Console Table. This simple build is just so stylish, yahoo! I can’t wait to see who gives this collection a try first…
- Tape Measure
- Saw – Jig, Circular, or Miter
- Countersink Bit for Drill
- Kreg Jig
- 2 – 1×2 at 6’
- 1 – 2×2 at 4’
- 3 – 1×3 at 8’
- 1-1/4” pocket hole screws
- 2” pocket hole screws
- 1-1/4” screws
- 1-1/2” screws
- One 18” x 45” piece of Plexiglas
- Clear rubber bumpers (to place the glass on the frame)
- Wood filler
- Wood glue
- Finishing Supplies
- 2 – 1×2 at 10-11/16” – Frame
- 2 – 1×2 at 41” – Frame
- 1 – 2×2 at 38” – Stretcher
- 4 – 1×3 at 32-5/16” – X
- 4 – 1×3 at 15-9/16” – X
- 4 – 1×3 at 15-3/4” – X
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Cut the pieces for the Xs. Cut the angles as shown – they are NOT 45 deg angles! Set the Kreg jig for ¾” material and drill pocket holes in the shorter pieces as shown. Assemble the Xs using glue and 1-1/4” pocket hole screws maintaining the dimensions as shown. Attach two X assemblies to each other (with the pocket holes facing in) using glue and countersunk 1-1/4” screws.
Cut the piece for the stretcher. Set the Kreg jig for 1-1/2” material and drill pocket holes at each end. Attach to the center of each X assembly using glue and 2” pocket hole screws.
Cut the pieces for the frame. Set the Kreg jig for ¾” material and drill pocket holes in each end of the shorter pieces. Assemble as shown using glue and 1-1/4” pocket hole screws. Position the frame on the X assemblies with the pocket holes facing down and secure using glue and 1-1/2” countersunk screws.
Position the rubber bumpers on the frame and set the Plexiglass on top.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.